Seagate ST31000640SSIM Transmitter signal characteristics, Signal characteristica Units Gbps

Page 69

9.5.2.2Transmitter signal characteristics

Table 16 specifies the signal requirements at the transmitter end of a TxRx connection as measured into the zero-length test load. All specifications are based on differential measurements.

The OOB sequence is performed at signal voltage levels corresponding to the lowest supported transfer rate. Table 16 specifies the signal characteristics.

Table 16: Transmitter signal characteristics

Signal characteristica	Units	1.5 Gbps	3.0 Gbps
Skewb	ps	20	15
Tx Off Voltagec	mV(P-P)	< 50	< 50
Maximum rise/fall timed	ps	273	137
Minimum rise/fall timed	ps	67	67
Maximum transmitter output imbalancee	%	10	10
OOB offset deltaf	mV	± 25	± 25
OOB common mode deltag	mV	± 50	± 50

aAll tests in this table shall be performed with zero-length test load shown in figure 20.

bThe skew measurement shall be made at the midpoint of the transition with a repeating 0101b pattern on the physical link. The same stable trigger, coherent to the data stream, shall be used for both the Tx+ and Tx- signals. Skew is defined as the time difference between the means of the midpoint crossing times of the Tx+ signal and the Tx- signal.

cThe transmitter off voltage is the maximum A.C. voltage measured at compliance points when the transmitter is unpowered or transmitting D.C. idle (e.g., during idle time of an OOB signal).

dRise/fall times are measured from 20 % to 80 % of the transition with a repeating 0101b pattern on the physical link.

eThe maximum difference between the V+ and V- A.C. RMS transmitter amplitudes measured on a CJTPAT test pattern (see 9.5.2.3.3) into the test load shown in figure 20, as a percentage of the average of the V+ and V- A.C. RMS amplitudes.

fThe maximum difference in the average differential voltage (D.C. offset) component between the burst times and the idle times of an OOB signal.

gThe maximum difference in the average of the common mode voltage between the burst times and the idle times of an OOB signal.

Barracuda ES.2 SAS Product Manual, Rev. G

63

Image 69

Contents ST31000640SS ST3750630SS ST3500620SS Barracuda ES.2 SASPage Reliability specifications Performance characteristicsPhysical/electrical specifications General descriptionDefect and error management InstallationInterface requirements Seagate Technology Support Services Barracuda ES.2 SAS Product Manual, Rev Scope Barracuda ES.2 SAS Product Manual, Rev. G Standards Standards, compliance and reference documentsElectromagnetic compatibility Electromagnetic susceptibilityCompliance Reference documents Barracuda ES.2 SAS Product Manual, Rev. G Barracuda ES.2 drive illustration General descriptionMedia description Standard featuresPerformance ReliabilityFactory-installed options Formatted capacitiesProgrammable drive capacity Barracuda ES.2 SAS Product Manual, Rev. G Internal drive characteristics Performance characteristicsAccess time Seek performanceFormat command execution time minutes General performance characteristicsStart/stop time Prefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Error rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlTemperature Log Page 0Dh Predictive failuresThermal monitor DST failure definition State of the drive prior to testingImplementation Invoking DSTShort test Function Code 001b Product warrantyExtended test Function Code 010b Log page entriesProduct repair and return information ShippingBarracuda ES.2 SAS Product Manual, Rev. G AC power requirements Physical/electrical specificationsDC power requirements ST31000640SS DC power requirementsST3500620SS DC power requirements ST3750630SS DC power requirementsPower sequencing General DC power requirement notesConducted noise immunity Current profilesTypical ST31000640SS drive +5V and +12V current profiles Typical ST3500620SS drive +5V and +12V current profiles Power dissipationBarracuda ES.2 SAS Product Manual, Rev. G Environmental limits Temperature a. OperatingEffective altitude sea level a. Operating Relative humidityShock and vibration ShockPackage size Packaged/product weight Drop height Vibration a. Operating-normal Air cleanlinessAcoustics Corrosive environmentSee Section Barracuda ES.2 SAS Product Manual, Rev. G Physical dimensions Mechanical specificationsDefect and error management Drive internal defects/errorsDrive error recovery procedures 108.29 SAS system errors Background Media ScanMedia Pre-Scan Idle Read After Write Deferred Auto-ReallocationDrive orientation InstallationAir flow CoolingGrounding Drive mountingBarracuda ES.2 SAS Product Manual, Rev. G Interface requirements SAS featuresDual port support Scsi commands supported Commands supported by Barracuda ES.2 SAS family drivesCommand name Command code Supported Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Mode Sense data Inquiry dataBarracuda ES.2 SAS inquiry data Bytes Data hex Page Mode Pages 2.1 ST31000640SS Mode Sense data2.2 ST3750630SS Mode Sense data 2.3 ST3500620SS Mode Sense data Miscellaneous features Miscellaneous operating features and conditionsSupported Feature or condition Miscellaneous statusSAS physical interface Datum B Connector requirements Physical characteristicsElectrical description Pin Signal name Signal typePin descriptions SAS pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutDifferential signals LED drive signalGeneral interface characteristics Eye masks Eye masks overviewJitter tolerance masks Receive eye maskAbsolute amplitude Normalized time in UISinusoidal Peak-toJitter Frequency in kHzSignal characteristica Units Gbps Transmitter signal characteristicsSignal characteristic Units Gbps Receiver signal characteristicsMaximum allowable jitter Gbps m, n Deterministic jitterqReceiver jitter tolerance Impedance specificationsCompliant jitter test pattern Cjtpat Impedance requirements Sheet 1Transmitter characteristics Impedance requirements Sheet 2Electrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Barracuda ES.2 SAS Product Manual, Rev. G