Seagate ST31000640SSIM manual Vibration a. Operating-normal, Acoustics, Air cleanliness

Page 38

6.4.4.2Vibration a. Operating—normal

The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding

5 - 22 Hz

0.25

Gs, Limited displacement

22 - 350 Hz

0.5 Gs

350 - 500 Hz

0.25

Gs

Vibration may be applied in the X, Y, or Z axis.

b.Operating—abnormal

Equipment as installed for normal operation shall not incur physical damage while subjected to periodic vibration not exceeding:

15 minutes of duration at major resonant frequency

Vibration occurring at these levels may degrade operational performance during the abnormal vibration period. Specified operational performance will continue when normal operating vibration levels are resumed. This assumes system recovery routines are available.

Operating abnormal translational random flat profile

5 - 500 Hz

0.75 Gs (0 to peak)

c.Non-operating

The limits of non-operating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives.

The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding

5 - 22 Hz

2 Gs (0 to peak, linear, swept sine, 0.5 octive/min)

22 - 350 Hz

5

Gs (0 to peak, linear, swept sine, 0.5 octive/min)

350 - 500 Hz

2

Gs (0 to peak, linear, swept sine, 0.5 octave/min)

Vibration may be applied in the X, Y, or Z axis.

6.4.5Acoustics

Sound power during idle mode shall be 2.9 bels typical when measured to ISO 7779 specification. Sound power while operating shall be 3.2 bels typical when measured to ISO 7779 specification.

There will not be any discrete tones more than 10 dB above the masking noise on typical drives when mea- sured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the masking noise on any drive.

6.4.6Air cleanliness

The drive is designed to operate in a typical office environment with minimal environmental control.

6.4.7Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro- sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil- ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or

32

Barracuda ES.2 SAS Product Manual, Rev. G

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Barracuda ES.2 SAS ST31000640SS ST3750630SS ST3500620SSPage Physical/electrical specifications Performance characteristicsReliability specifications General descriptionInterface requirements Defect and error managementInstallation Seagate Technology Support Services Barracuda ES.2 SAS Product Manual, Rev Scope Barracuda ES.2 SAS Product Manual, Rev. G Electromagnetic compatibility Standards, compliance and reference documentsStandards Electromagnetic susceptibilityCompliance Reference documents Barracuda ES.2 SAS Product Manual, Rev. G General description Barracuda ES.2 drive illustrationPerformance Standard featuresMedia description ReliabilityProgrammable drive capacity Factory-installed optionsFormatted capacities Barracuda ES.2 SAS Product Manual, Rev. G Access time Performance characteristicsInternal drive characteristics Seek performanceStart/stop time Format command execution time minutesGeneral performance characteristics Caching write data Prefetch/multi-segmented cache controlCache operation Prefetch operation Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlThermal monitor Temperature Log Page 0DhPredictive failures Implementation State of the drive prior to testingDST failure definition Invoking DSTExtended test Function Code 010b Product warrantyShort test Function Code 001b Log page entriesShipping Product repair and return informationBarracuda ES.2 SAS Product Manual, Rev. G DC power requirements Physical/electrical specificationsAC power requirements ST31000640SS DC power requirementsST3750630SS DC power requirements ST3500620SS DC power requirementsConducted noise immunity General DC power requirement notesPower sequencing Current profilesTypical ST31000640SS drive +5V and +12V current profiles Power dissipation Typical ST3500620SS drive +5V and +12V current profilesBarracuda ES.2 SAS Product Manual, Rev. G Temperature a. Operating Environmental limitsShock and vibration Relative humidityEffective altitude sea level a. Operating ShockPackage size Packaged/product weight Drop height Acoustics Air cleanlinessVibration a. Operating-normal Corrosive environmentSee Section Barracuda ES.2 SAS Product Manual, Rev. G Mechanical specifications Physical dimensionsDrive error recovery procedures Defect and error managementDrive internal defects/errors 108.29 Media Pre-Scan SAS system errorsBackground Media Scan Deferred Auto-Reallocation Idle Read After WriteInstallation Drive orientationCooling Air flowDrive mounting GroundingBarracuda ES.2 SAS Product Manual, Rev. G SAS features Interface requirementsDual port support Command name Command code Supported Scsi commands supportedCommands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Barracuda ES.2 SAS inquiry data Bytes Data hex Mode Sense dataInquiry data Page 2.1 ST31000640SS Mode Sense data Mode Pages2.2 ST3750630SS Mode Sense data 2.3 ST3500620SS Mode Sense data Supported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusSAS physical interface Datum B Physical characteristics Connector requirementsPin descriptions Pin Signal name Signal typeElectrical description SAS pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutGeneral interface characteristics LED drive signalDifferential signals Eye masks Eye masks overviewAbsolute amplitude Receive eye maskJitter tolerance masks Normalized time in UIJitter Peak-toSinusoidal Frequency in kHzTransmitter signal characteristics Signal characteristica Units GbpsMaximum allowable jitter Receiver signal characteristicsSignal characteristic Units Gbps Gbps m, n Deterministic jitterqCompliant jitter test pattern Cjtpat Impedance specificationsReceiver jitter tolerance Impedance requirements Sheet 1Electrical TxRx connections Transmitter characteristicsImpedance requirements Sheet 2 = -5,437dB Shows the zero-length test load Receiver characteristics Barracuda ES.2 SAS Product Manual, Rev. G
Top Page Image Contents