Seagate ST31000640SSIM manual Start/stop time, Format command execution time minutes

Page 18

4.2.2Format command execution time (minutes)

	ST31000640SS	ST3750630SS	ST3500620SS
Maximum (with verify)	400	300	200
Maximum (without verify)	200	150	100

Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the request for a Status Byte Transfer to the Initiator (excluding connect/disconnect).

4.2.3	General performance characteristics
Sustainable disk transfer rate*:
Minimum		56 Mbytes/sec
Maximum		116 Mbytes/sec
SAS Interface maximum instantaneous transfer rate		300 Mbytes/sec* per port
		(dual port = 600 Mbytes/sec*)
Logical block sizes
Default is 512-byte data blocks
Sector sizes variable to 512, 520, 524, and 528 kbytes.
Read/write consecutive sectors on a track		Yes
Flaw reallocation performance impact (for flaws reallocated at format time using		Negligible
the spare sectors per sparing zone reallocation scheme.)

*Assumes no errors and no relocated logical blocks. Rate measured from the start of the first logical block transfer to or from the host.

4.3Start/stop time

The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has been applied.

If the drive receives a NOTIFY (ENABLE SPINUP) primitive through either port and has not received a START STOP UNIT command with the START bit equal to 0, the drive becomes ready for normal operations within 20 seconds (excluding the error recovery procedure).

If the drive receives a START STOP UNIT command with the START bit equal to 0 before receiving a NOTIFY (ENABLE SPINUP) primitive, the drive waits for a START STOP UNIT command with the START bit equal to 1. After receiving a START STOP UNIT command with the START bit equal to 1, the drive waits for a NOTIFY (ENABLE SPINUP) primitive. After receiving a NOTIFY (ENABLE SPINUP) primitive through either port, the drive becomes ready for normal operations within 20 seconds (excluding the error recovery procedure).

If the drive receives a START STOP UNIT command with the START bit and IMMED bit equal to 1 and does not receive a NOTIFY (ENABLE SPINUP) primitive within 5 seconds, the drive fails the START STOP UNIT command.

The START STOP UNIT command may be used to command the drive to stop the spindle. Stop time is 20 sec- onds (maximum) from removal of DC power.

There is no power control switch on the drive.

12	Barracuda ES.2 SAS Product Manual, Rev. G

Image 18

Contents Barracuda ES.2 SAS ST31000640SS ST3750630SS ST3500620SSPage Physical/electrical specifications Performance characteristicsReliability specifications General descriptionDefect and error management InstallationInterface requirements Seagate Technology Support Services Barracuda ES.2 SAS Product Manual, Rev Scope Barracuda ES.2 SAS Product Manual, Rev. G Electromagnetic compatibility Standards, compliance and reference documentsStandards Electromagnetic susceptibilityCompliance Reference documents Barracuda ES.2 SAS Product Manual, Rev. G General description Barracuda ES.2 drive illustrationPerformance Standard featuresMedia description ReliabilityFactory-installed options Formatted capacitiesProgrammable drive capacity Barracuda ES.2 SAS Product Manual, Rev. G Access time Performance characteristicsInternal drive characteristics Seek performanceFormat command execution time minutes General performance characteristicsStart/stop time Prefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlTemperature Log Page 0Dh Predictive failuresThermal monitor Implementation State of the drive prior to testingDST failure definition Invoking DSTExtended test Function Code 010b Product warrantyShort test Function Code 001b Log page entriesShipping Product repair and return informationBarracuda ES.2 SAS Product Manual, Rev. G DC power requirements Physical/electrical specificationsAC power requirements ST31000640SS DC power requirementsST3750630SS DC power requirements ST3500620SS DC power requirementsConducted noise immunity General DC power requirement notesPower sequencing Current profilesTypical ST31000640SS drive +5V and +12V current profiles Power dissipation Typical ST3500620SS drive +5V and +12V current profilesBarracuda ES.2 SAS Product Manual, Rev. G Temperature a. Operating Environmental limitsShock and vibration Relative humidityEffective altitude sea level a. Operating ShockPackage size Packaged/product weight Drop height Acoustics Air cleanlinessVibration a. Operating-normal Corrosive environmentSee Section Barracuda ES.2 SAS Product Manual, Rev. G Mechanical specifications Physical dimensionsDefect and error management Drive internal defects/errorsDrive error recovery procedures 108.29 SAS system errors Background Media ScanMedia Pre-Scan Deferred Auto-Reallocation Idle Read After WriteInstallation Drive orientationCooling Air flowDrive mounting GroundingBarracuda ES.2 SAS Product Manual, Rev. G SAS features Interface requirementsDual port support Scsi commands supported Commands supported by Barracuda ES.2 SAS family drivesCommand name Command code Supported Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Mode Sense data Inquiry dataBarracuda ES.2 SAS inquiry data Bytes Data hex Page 2.1 ST31000640SS Mode Sense data Mode Pages2.2 ST3750630SS Mode Sense data 2.3 ST3500620SS Mode Sense data Supported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusSAS physical interface Datum B Physical characteristics Connector requirementsPin descriptions Pin Signal name Signal typeElectrical description SAS pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutGeneral interface characteristics LED drive signalDifferential signals Eye masks Eye masks overviewAbsolute amplitude Receive eye maskJitter tolerance masks Normalized time in UIJitter Peak-toSinusoidal Frequency in kHzTransmitter signal characteristics Signal characteristica Units GbpsMaximum allowable jitter Receiver signal characteristicsSignal characteristic Units Gbps Gbps m, n Deterministic jitterqCompliant jitter test pattern Cjtpat Impedance specificationsReceiver jitter tolerance Impedance requirements Sheet 1Transmitter characteristics Impedance requirements Sheet 2Electrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Barracuda ES.2 SAS Product Manual, Rev. G