Seagate ST9146603SS, ST9300603SS manual Reliability and service, Seek errors, Interface errors

Page 23

6.1.3Seek errors

A seek error is defined as a failure of the drive to position the heads to the addressed track. After detecting an initial seek error, the drive automatically performs an error recovery process. If the error recovery process fails, a seek positioning error (Error code = 15h or 02h) will be reported with a Hardware error (04h) in the Sense Key. Recoverable seek errors are specified at Less than 10 errors in 108 seeks. Unrecoverable seek errors (Sense Key = 04h) are classified as drive failures.

6.1.4Interface errors

An interface error is defined as a failure of the receiver on a port to recover the data as transmitted by the device port connected to the receiver. The error may be detected as a running disparity error, illegal code, loss of word sync, or CRC error.

6.2Reliability and service

You can enhance the reliability of Savvio disc drives by ensuring that the drive receives adequate cooling. Sec- tion 7.0 provides temperature measurements and other information that may be used to enhance the service life of the drive. Section 11.2 provides recommended air-flow information.

6.2.1Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)

The production disc drive shall achieve an AFR of 0.55% (MTBF of 1,600,000 hours) when operated in an environment that ensures the HDA case temperatures do not exceed the values specified in Section 7.4. Oper- ation at case temperatures outside the specifications in Section 7.4 may increase the product AFR (decrease the MTBF). The AFR (MTBF) is a population statistic not relevant to individual units.

The AFR (MTBF) specification is based on the following assumptions for Enterprise Storage System environ- ments:

•8,760 power-on hours per year.

•250 average on/off cycles per year.

•Operations at nominal voltages.

•Systems will provide adequate cooling to ensure the case temperatures specified in Section 7.4 are not exceeded. Temperatures outside the specifications in Section 7.4 will increase the product AFR and decrease the MTBF.

6.2.2Preventive maintenance

No routine scheduled preventive maintenance is required.

6.2.3Hot plugging the drive

When a disc is powered on by switching the power or hot plugged, the drive runs a self test before attempting to communicate on its’ interfaces. When the self test completes successfully, the drive initiates a Link Reset starting with OOB. An attached device should respond to the link reset. If the link reset attempt fails, or any time the drive looses sync, the drive initiated link reset. The drive will initiate link reset once per second but alternates between port A and B. Therefore each port will attempt a link reset once per 2 seconds assuming both ports are out of sync.

If the self-test fails, the drive does not respond to link reset on the failing port.

Note. It is the responsibility of the systems integrator to assure that no temperature, energy, voltage haz- ard, or ESD potential hazard is presented during the hot connect/disconnect operation. Discharge the static electricity from the drive carrier prior to inserting it into the system.

Savvio 10K.3 SAS Product Manual, Rev. G

15

Page 22 Page 24
Image 23
Page 22 Page 24
Contents SED Fips 140-2 Models ST9300603SSST9300503SS ST9146803SSST9146703SSST9300403SS ST9146603SS Standard Models Self-Encrypting Drive ModelsPage Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPage Savvio 10K.3 SAS Product Manual, Rev. G List of Figures Page Seagate Online Support and Services Seagate Technology support servicesScope Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean MIC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresProgrammable drive capacity PerformanceReliability Formatted capacitiesFactory-installed options Access time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCaching write data Prefetch/multi-segmented cache controlCache operation Prefetch operation Unrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct repair and return information Product warrantyShipping DC power requirements Physical/electrical specificationsAC power requirements Savvio 10K.3 SAS Product Manual, Rev. G Page Conducted noise immunity General DC power requirement notesPower sequencing Current profiles for 300GB models Current profilesCurrent profiles for 146GB models GB models in 3 Gbit operation Power dissipation300GB models in 6 Gbit operation 146GB models in 3 Gbit operation 146GB models in 6 Gbit operation Temperature a. OperatingEnvironmental limits Shock and vibration Relative humidityEffective altitude sea level a. Operating Shock Recommended mounting Vibration a. Operating-normalAcoustics Air cleanlinessCorrosive environment Mounting configuration dimensions Mechanical specificationsLevel 2 security About FipsPurpose Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Default passwordRandom number generator RNG Drive lockingCryptographic erase Authenticated firmware downloadPower requirements Supported commandsDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media ScanMedia Pre-Scan Idle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Savvio inquiry data Mode Sense dataInquiry data Page Mode Pages Mode Sense data for 300GB drivesMode Sense values for 146GB drives Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification complianceLED drive signal Differential signalsSavvio 10K.3 SAS Product Manual, Rev. G Numerics IndexKCC Msid Mtbf See also cooling Page Seagate Technology LLC

ST9146803SS, ST9300603SS, ST9300503SS, ST9146603SS, ST9146703SS specifications

Seagate has long been a key player in the storage technology industry, and its enterprise-class hard drives such as the ST9300503SS, ST9300403SS, ST9146603SS, ST9146803SS, and ST9146703SS stand out for their performance, reliability, and innovative features. Designed primarily for use in data centers and server environments, these drives offer a range of specifications suited for high-demand applications.

The Seagate ST9300503SS is a 300GB 2.5-inch SAS (Serial Attached SCSI) hard drive that operates at 10,000 RPM, which is essential for ensuring rapid data access. It provides a data transfer rate of 6 Gb/s and features Seagate's AgileArray technology, which enhances RAID performance and reliability by improving data integrity and optimizing power consumption. The drive is also designed to withstand the rigors of enterprise use, boasting a mean time between failures (MTBF) rating of 1.6 million hours.

In contrast, the ST9300403SS offers a similar 300GB capacity and speed, but with slight variations in features that make it better suited for specific applications. This drive also supports SAS 2.0 and includes features that enhance error recovery and data protection.

The ST9146603SS is another powerhouse, providing 146GB of storage. Operating at the same high spindle speed of 10,000 RPM, it is optimized for low-latency performance. This makes it highly suitable for transactional applications and environments where quick access to data is crucial. Like its counterparts, this drive is built with robust technologies that ensure reliable operation and enhanced data security.

The ST9146803SS bumps up the storage capacity to 300GB while maintaining the same impressive speed and performance features. Its incorporation of Seagate’s SeaTach technology allows for advanced communication protocols, which facilitate faster data transfers and lower latency.

Finally, the ST9146703SS also offers 146GB of storage and is known for its energy efficiency features that reduce operational costs in large-scale deployments. All these drives support a wide range of operating systems, making them versatile picks for businesses looking to upgrade their storage solutions.

Overall, the Seagate ST9300503SS, ST9300403SS, ST9146603SS, ST9146803SS, and ST9146703SS are essential components in any enterprise environment, delivering high performance, reliability, and advanced technology features that meet the critical demands of modern data storage.
Top Page Image Contents