Seagate ST9300403SS Drive Self Test DST, DST failure definition, Implementation, Invoking DST

Page 26

6.2.6Drive Self Test (DST)

Drive Self Test (DST) is a technology designed to recognize drive fault conditions that qualify the drive as a failed unit. DST validates the functionality of the drive at a system level.

There are two test coverage options implemented in DST:

1.Extended test

2.Short test

The most thorough option is the extended test that performs various tests on the drive and scans every logical block address (LBA) of the drive. The short test is time-restricted and limited in length—it does not scan the entire media surface, but does some fundamental tests and scans portions of the media.

If DST encounters an error during either of these tests, it reports a fault condition. If the drive fails the test, remove it from service and return it to Seagate for service.

6.2.6.1DST failure definition

The drive will present a “diagnostic failed” condition through the self-tests results value of the diagnostic log page if a functional failure is encountered during DST. The channel and servo parameters are not modified to test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number of retries required to recover the data.

The following conditions are considered DST failure conditions:

•Seek error after retries are exhausted

•Track-follow error after retries are exhausted

•Read error after retries are exhausted

•Write error after retries are exhausted

Recovered errors will not be reported as diagnostic failures.

6.2.6.2Implementation

This section provides all of the information necessary to implement the DST function on this drive.

6.2.6.2.1State of the drive prior to testing

The drive must be in a ready state before issuing the Send Diagnostic command. There are multiple reasons why a drive may not be ready, some of which are valid conditions, and not errors. For example, a drive may be in process of doing a format, or another DST. It is the responsibility of the host application to determine the “not ready” cause.

While not technically part of DST, a Not Ready condition also qualifies the drive to be returned to Seagate as a failed drive.

A Drive Not Ready condition is reported by the drive under the following conditions:

•Motor will not spin

•Motor will not lock to speed

•Servo will not lock on track

•Drive cannot read configuration tables from the disc

In these conditions, the drive responds to a Test Unit Ready command with an 02/04/00 or 02/04/03 code.

6.2.6.2.2Invoking DST

To invoke DST, submit the Send Diagnostic command with the appropriate Function Code (001b for the short test or 010b for the extended test) in bytes 1, bits 5, 6, and 7.

18

Savvio 10K.3 SAS Product Manual, Rev. G

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Standard Models Self-Encrypting Drive Models ST9300603SSST9300503SS ST9146803SSST9146703SSST9300403SS ST9146603SS SED Fips 140-2 ModelsPage Contents About Fips About self-encrypting drives Defect and error managementInstallation Interface requirementsPage Savvio 10K.3 SAS Product Manual, Rev. G List of Figures Page Seagate Technology support services Seagate Online Support and ServicesScope Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean MICReference documents European Union Restriction of Hazardous Substances RoHSGeneral description Standard features Media descriptionFormatted capacities PerformanceReliability Programmable drive capacityFactory-installed options Seek performance characteristics Performance characteristicsInternal drive characteristics Access timeGeneral performance characteristics Start/stop timeCaching write data Prefetch/multi-segmented cache controlCache operation Prefetch operation Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures DST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesProduct repair and return information Product warrantyShipping DC power requirements Physical/electrical specificationsAC power requirements Savvio 10K.3 SAS Product Manual, Rev. G Page Conducted noise immunity General DC power requirement notesPower sequencing Current profiles Current profiles for 300GB modelsCurrent profiles for 146GB models Power dissipation GB models in 3 Gbit operation300GB models in 6 Gbit operation 146GB models in 3 Gbit operation 146GB models in 6 Gbit operation Temperature a. OperatingEnvironmental limits Shock and vibration Relative humidityEffective altitude sea level a. Operating Shock Vibration a. Operating-normal Recommended mountingAcoustics Air cleanlinessCorrosive environment Mechanical specifications Mounting configuration dimensionsLevel 2 security About FipsPurpose About self-encrypting drives Controlled accessAdmin SP Data encryptionDrive locking Default passwordRandom number generator RNG Data bandsSupported commands Authenticated firmware downloadPower requirements Cryptographic eraseDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media ScanMedia Pre-Scan Idle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsSupported commands Supported commands Supported commands Savvio inquiry data Mode Sense dataInquiry data Page Mode Sense data for 300GB drives Mode PagesMode Sense values for 146GB drives Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutDifferential signals SAS-2 Specification complianceLED drive signal General interface characteristicsSavvio 10K.3 SAS Product Manual, Rev. G Index NumericsKCC Msid Mtbf See also cooling Page Seagate Technology LLC

ST9146803SS, ST9300603SS, ST9300503SS, ST9146603SS, ST9146703SS specifications

Seagate has long been a key player in the storage technology industry, and its enterprise-class hard drives such as the ST9300503SS, ST9300403SS, ST9146603SS, ST9146803SS, and ST9146703SS stand out for their performance, reliability, and innovative features. Designed primarily for use in data centers and server environments, these drives offer a range of specifications suited for high-demand applications.

The Seagate ST9300503SS is a 300GB 2.5-inch SAS (Serial Attached SCSI) hard drive that operates at 10,000 RPM, which is essential for ensuring rapid data access. It provides a data transfer rate of 6 Gb/s and features Seagate's AgileArray technology, which enhances RAID performance and reliability by improving data integrity and optimizing power consumption. The drive is also designed to withstand the rigors of enterprise use, boasting a mean time between failures (MTBF) rating of 1.6 million hours.

In contrast, the ST9300403SS offers a similar 300GB capacity and speed, but with slight variations in features that make it better suited for specific applications. This drive also supports SAS 2.0 and includes features that enhance error recovery and data protection.

The ST9146603SS is another powerhouse, providing 146GB of storage. Operating at the same high spindle speed of 10,000 RPM, it is optimized for low-latency performance. This makes it highly suitable for transactional applications and environments where quick access to data is crucial. Like its counterparts, this drive is built with robust technologies that ensure reliable operation and enhanced data security.

The ST9146803SS bumps up the storage capacity to 300GB while maintaining the same impressive speed and performance features. Its incorporation of Seagate’s SeaTach technology allows for advanced communication protocols, which facilitate faster data transfers and lower latency.

Finally, the ST9146703SS also offers 146GB of storage and is known for its energy efficiency features that reduce operational costs in large-scale deployments. All these drives support a wide range of operating systems, making them versatile picks for businesses looking to upgrade their storage solutions.

Overall, the Seagate ST9300503SS, ST9300403SS, ST9146603SS, ST9146803SS, and ST9146703SS are essential components in any enterprise environment, delivering high performance, reliability, and advanced technology features that meet the critical demands of modern data storage.
Top Page Image Contents