Seagate ST318405LW/LC, ST39205LW/LC manual Drive orientation, Cooling, Drive mounting, Grounding

Page 54

44

Cheetah 36XL Product Manual, Rev. E

8.2Drive orientation

The balanced rotary arm actuator design of the drive allows it to be mounted in any orientation. All drive perfor- mance characterization, however, has been done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, and these are the two preferred mounting orientations.

8.3Cooling

Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding the drive will not exceed temperature conditions specified in Section 6.4.1, “Temperature.” Specific consider- ation should be given to make sure adequate air circulation is present around the printed circuit board (PCB) to meet the requirements of Section 6.4.1, “Temperature.”

8.4Drive mounting

When mounting the drive using the bottom holes (x-y plane in Figure 13) care must be taken to ensure that the drive is not physically distorted due to a stiff non-flat mounting surface. The allowable mounting surface stiff- ness is 80 lb/in (14.0 N/mm). The following equation and paragraph define the allowable mounting surface stiff- ness:

k * x = F < 15lb = 67N

where ‘k’ represents the mounting surface stiffness (units of lb/in or N/mm), and ‘x’ represents the out-of-plane mounting surface distortion (units of inches or millimeters). The out-of-plane distortion (‘x’) is determined by defining a plane with three of the four mounting points fixed and evaluating the out-of-plane deflection of the fourth mounting point when a known force (F) is applied to the fourth point.

Note. Before mounting the drive in any kind of 3.5-inch to 5.25-inch adapter frame, verify with Seagate Tech- nology that the drive can meet the shock and vibration specifications given herein while mounted in such an adapter frame. Adapter frames that are available may not have a mechanical structure capa- ble of mounting the drive so that it can meet the shock and vibration specifications listed in this manual.

8.5Grounding

Signal ground (PCBA) and HDA ground are connected together in the drive and cannot be separated by the user. The equipment in which the drive is mounted is connected directly to the HDA and PCBA with no electri- cally isolating shock mounts. If it is desired for the system chassis to not be connected to the HDA/PCBA ground, the systems integrator or user must provide a nonconductive (electrically isolating) method of mount- ing the drive in the host equipment.

Increased radiated emissions may result if you do not provide the maximum surface area ground connection between system ground and drive ground. This is the system designer’s and integrator’s responsibility.

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Cheetah 36XL Family ST336705LW/LC ST318405LW/LC ST39205LW/LC Page Cheetah 36XL Family ST336705LW/LC ST318405LW/LC ST39205LW/LC Page Revision status summary sheet Revision Date Writer/Engineer Sheets AffectedPage Contents Seagate Technology support services Defect and error managementInstallation Interface requirementsList of Figures Cheetah 36XL Product Manual, Rev. E ViiPage Scope Cheetah 36XL family drive ST336705LC shownCheetah 36XL Product Manual, Rev. E Applicable standards and reference documentation Australian C-Tick Korean MICTaiwanese Bsmi General description Cheetah 36XL family drive Performance Cheetah 36XL Product Manual, Rev. E Standard featuresMedia characteristics ReliabilityFormatted capacities Factory installed accessoriesOptions factory installed Programmable drive capacityPerformance characteristics Ultra2 Scsi Ultra160 Scsi Start/stop timePrefetch/multi-segmented cache control Cache operation Caching write dataPrefetch operation Cheetah 36XL Product Manual, Rev. E Cheetah 36XL Product Manual, Rev. E Reliability specifications Service life Reliability and servicePreventive maintenance Service philosophy7 S.M.A.R.T Controlling S.M.A.R.TDetermining rate Performance impactReporting control Predictive failuresImplementation State of the drive prior to testingDST Failure Definition Invoking DSTExtended test Function Code 010b Product warrantyShort test Function Code 001b Log page entriesProduct repair and return information Cheetah 36XL Product Manual, Rev. E Physical/electrical specifications AC power requirementsDC power requirements Power sequencing Conducted noise immunity3 12 V Current profile Typical ST336705 drive +12 V current profile Typical ST39205 drive +12 V current profile TypicalST318405 drive +5 V current profile Power dissipation ST336705 Cheetah 36XL Product Manual, Rev. E ST318405 Os per SecondTemperature ST39205Environmental limits Shock and vibration Relative humidityEffective altitude sea level ShockPackage size Packaged/product weight Drop height Recommended mounting Air cleanliness VibrationAcoustics LW mounting configuration dimensions LC mounting configuration dimensions Defect and error management Drive error recovery proceduresDrive internal defects Scsi systems errors Formatting InstallationConfigure drive options Drive ID/option select headerDo not install jumpers retain cover J5 jumper header on LW model only J2 option select header Cheetah 36XL Product Manual, Rev. E Function description Does not apply to LC modelsDrive mounting Drive orientationCooling GroundingInterface requirements Scsi interface messages supportedScsi interface commands supported Cheetah 36XL Product Manual, Rev. E Commands supported by Cheetah 36XL family drive Mode Sense data Inquiry Vital Product dataCheetah 36XL Product Manual, Rev. E Mode Sense Data Cheetah 36XL Product Manual, Rev. E Mode sense data, ST318405 values Bytes Cheetah 36XL Product Manual, Rev. E Mode sense data, ST39205 values Bytes Cheetah 36XL Product Manual, Rev. E Condition/features supported DC cable and connector 2 REQ/ACK offsetPhysical interface Pin Power Scsi interface physical description Scsi interface cable requirementsMating connectors for LC model drives Mating connectorsMating connectors for LW model drives ST336705LC, ST318405LC and ST39205LCRight-angle to Pcba connectors Scsi IDNonshielded 68 pin Scsi device connector used on LW drives Nonshielded 80 pin Scsi SCA-2 connector, used on LC drives GND +DBP1 Charge 68Cheetah 36XL Product Manual, Rev. E Multimode signals Electrical descriptionMultimode-SE and LVD alternatives Output characteristics Input characteristicsLow voltage differential I/O circuits General cable characteristicsTerminator requirements Terminator power LW drives LC drivesDisc drive Scsi timing Drive activity remote LED signal status Cheetah 36XL Product Manual, Rev. E Presales Support Seagate Technology support services Online ServicesAutomated Services Technical SupportCustomer Service CSO USA/Canada/Latin America Support ServicesEuropean Support Services Africa/Middle East Support Services Asia/Pacific Support ServicesCall Center Toll-free Direct dial Cheetah 36XL Product Manual, Rev. E Index Symbols Cheetah 36XL Product Manual, Rev. E LED PCB System chassis Page
Top Page Image Contents