Seagate ST318405LW/LC, ST39205LW/LC, ST336705LW/LC manual Scsi systems errors

Page 48

38

Cheetah 36XL Product Manual, Rev. E

Table 3: Read and write retry count maximum recovery times [1]

Read retry

Maximum recovery time per

count [1]

LBA (cumulative, msec)

 

 

 

 

0

78

 

 

1

90

 

 

2

306

 

 

3

330

 

 

4

378

 

 

5

426

 

 

6

546

 

 

7

696

 

 

8

720

 

 

9

774

 

 

10

846

 

 

11 (default)

1569

 

 

Write retry

Maximum recovery time per

count

LBA (cumulative, msec)

 

 

 

 

0

66

 

 

1

84

 

 

2

126

 

 

3

144

 

 

4

252

 

 

5

294

 

 

6

498

 

 

7

516

 

 

8

546

 

 

9

564

 

 

10

1200

 

 

11

1218

 

 

12

1260

 

 

13

1278

 

 

14

1386

 

 

15 (default)

1428

 

 

[1]These values are subject to change.

Setting these retry counts to a value below the default setting could result in an increased unrecovered error rate which may exceed the value given in this product manual. A setting of zero (0) will result in the drive not performing error recovery.

For example, suppose the Read/Write Recovery page has the RC bit set to 0, read retry count set to 4, and the recovery time limit field (Mode Sense page 01, bytes 10 and 11) set to FF FF hex (maximum). A four LBA Read command is allowed to take up to 378 msec recovery time for each of the four LBAs in the command. If the recovery time limit is set to 00 C8 hex (200 msec decimal) a four LBA read command is allowed to take up to 200 msec for all error recovery within that command. The use of the Recovery Time Limit field allows finer granularity on control of the time spent in error recovery. The recovery time limit only starts counting when the drive is executing error recovery and it restarts on each command. Therefore, each command’s total recovery time is subject to the recovery time limit. Note: A recovery time limit of 0 will use the drive’s default value of FF FF. Minimum recovery time limit is achieved by setting the Recovery Time Limit field to 00 01.

7.3SCSI systems errors

Information on the reporting of operational errors or faults across the interface is given in the SCSI Interface Product Manual, part number 75789509. Message Protocol System is described in the SCSI Interface Product Manual. Several of the messages are used in the SCSI systems error management system. The Request Sense command returns information to the host about numerous kinds of errors or faults. The Receive Diag- nostic Results reports the results of diagnostic operations performed by the drive.

Status returned by the drive to the Initiator is described in the SCSI Interface Product Manual. Status reporting plays a role in the SCSI systems error management and its use in that respect is described in sections where the various commands are discussed.

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Cheetah 36XL Family ST336705LW/LC ST318405LW/LC ST39205LW/LC Page Cheetah 36XL Family ST336705LW/LC ST318405LW/LC ST39205LW/LC Page Revision status summary sheet Revision Date Writer/Engineer Sheets AffectedPage Contents Defect and error management InstallationSeagate Technology support services Interface requirementsList of Figures Cheetah 36XL Product Manual, Rev. E ViiPage Scope Cheetah 36XL family drive ST336705LC shownCheetah 36XL Product Manual, Rev. E Applicable standards and reference documentation Australian C-Tick Korean MICTaiwanese Bsmi General description Cheetah 36XL family drive Cheetah 36XL Product Manual, Rev. E Standard features Media characteristicsPerformance ReliabilityFactory installed accessories Options factory installedFormatted capacities Programmable drive capacityPerformance characteristics Ultra2 Scsi Ultra160 Scsi Start/stop timePrefetch/multi-segmented cache control Cache operation Caching write dataPrefetch operation Cheetah 36XL Product Manual, Rev. E Cheetah 36XL Product Manual, Rev. E Reliability specifications Reliability and service Preventive maintenanceService life Service philosophy7 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Reporting controlDetermining rate Predictive failuresState of the drive prior to testing DST Failure DefinitionImplementation Invoking DSTProduct warranty Short test Function Code 001bExtended test Function Code 010b Log page entriesProduct repair and return information Cheetah 36XL Product Manual, Rev. E Physical/electrical specifications AC power requirementsDC power requirements Power sequencing Conducted noise immunity3 12 V Current profile Typical ST336705 drive +12 V current profile Typical ST39205 drive +12 V current profile TypicalST318405 drive +5 V current profile Power dissipation ST336705 Cheetah 36XL Product Manual, Rev. E ST318405 Os per SecondTemperature ST39205Environmental limits Relative humidity Effective altitude sea levelShock and vibration ShockPackage size Packaged/product weight Drop height Recommended mounting Air cleanliness VibrationAcoustics LW mounting configuration dimensions LC mounting configuration dimensions Defect and error management Drive error recovery proceduresDrive internal defects Scsi systems errors Installation Configure drive optionsFormatting Drive ID/option select headerDo not install jumpers retain cover J5 jumper header on LW model only J2 option select header Cheetah 36XL Product Manual, Rev. E Function description Does not apply to LC modelsDrive orientation CoolingDrive mounting GroundingInterface requirements Scsi interface messages supportedScsi interface commands supported Cheetah 36XL Product Manual, Rev. E Commands supported by Cheetah 36XL family drive Mode Sense data Inquiry Vital Product dataCheetah 36XL Product Manual, Rev. E Mode Sense Data Cheetah 36XL Product Manual, Rev. E Mode sense data, ST318405 values Bytes Cheetah 36XL Product Manual, Rev. E Mode sense data, ST39205 values Bytes Cheetah 36XL Product Manual, Rev. E Condition/features supported DC cable and connector 2 REQ/ACK offsetPhysical interface Pin Power Scsi interface physical description Scsi interface cable requirementsMating connectors Mating connectors for LW model drivesMating connectors for LC model drives ST336705LC, ST318405LC and ST39205LCRight-angle to Pcba connectors Scsi IDNonshielded 68 pin Scsi device connector used on LW drives Nonshielded 80 pin Scsi SCA-2 connector, used on LC drives GND +DBP1 Charge 68Cheetah 36XL Product Manual, Rev. E Multimode signals Electrical descriptionMultimode-SE and LVD alternatives Output characteristics Input characteristicsGeneral cable characteristics Terminator requirements Terminator power LW drivesLow voltage differential I/O circuits LC drivesDisc drive Scsi timing Drive activity remote LED signal status Cheetah 36XL Product Manual, Rev. E Seagate Technology support services Online Services Automated ServicesPresales Support Technical SupportCustomer Service CSO USA/Canada/Latin America Support ServicesEuropean Support Services Africa/Middle East Support Services Asia/Pacific Support ServicesCall Center Toll-free Direct dial Cheetah 36XL Product Manual, Rev. E Index Symbols Cheetah 36XL Product Manual, Rev. E LED PCB System chassis Page
Top Page Image Contents