Western Telematic IPS-800-CE Installation, Power Supply Connection, Installing the Cable Keepers

Page 17

4. Installation

This Section provides further details regarding installation of the IPS unit.

4.1. Power Supply Connection

Use the supplied power cords to connect the IPS unit to an appropriate power supply. Note that the IPS’s Master Power Switch must be "On" in order for the unit to operate.

CAUTIONS:

•Before attempting to install this unit, please review the warnings and cautions listed at the front of the user's guide.

•This device should only be operated with the type of power source indicated on the instrument nameplate. If you are not sure of the type of power service available, please contact your local power company.

•Reliable earthing (grounding) of this unit must be maintained. Particular attention should be given to supply connections when connecting to power strips, rather than directly to the branch circuit.

4.1.1.Installing the Cable Keepers

The IPS includes cable keepers, which are designed to prevent the power supply cables from being accidentally disconnected from the unit.

•IPS-1600 and IPS-1600-CE:Sixteen-plug units include pre-installed cable keepers. When attaching the power supply cables to the unit, first swing the cable keepers out of the way, then plug the power cables securely into the power inputs. When the cables are in place, snap the cable keepers over each plug to secure the cables to the unit.

•IPS-800 and IPS-800-CE:The cable keeper for eight-plug units must be installed by the user. First make certain that both of the IPS's two power cables are disconnected from your power supply. Next, loosen (but do not remove) the retaining screws located adjacent to the power inlets. Connect the power supply cables to the IPS power inlets, then slip the cable keepers under each supply cable so the notches at the top of the keeper line up with each cable, and the two slots on the bottom of the keeper slide under the loosened retaining screws. Tighten the retaining screws to secure the cable keeper to the unit, make certain that the cables are secure, and then connect the cables to your power supply.

4-1

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Models User’s GuidePage Installation Instructions FCC Part 15 Regulation Table of Contents List of Figures Security Features and Co-Location Features Intelligent Power ControlEasy to Configure, Easy to Use IntroductionTypographic Conventions IPS-800, IPS-1600, IPS-800-CE and IPS-1600-CE UnitsIPS-800 Back Panel 120 VAC Model Shown Unit DescriptionIPS-800/IPS-1600 Series User’s Guide Quick Start Hardware InstallationApply Power to the IPS Connect your PC to the IPS Communicating with the IPSPlug Status Screen Web Browser Interface IPS-800 Shown Text Interface Text Interface Type /X and press Enter IPS-800/IPS-1600 Series User’s Guide Installing the Cable Keepers InstallationPower Supply Connection Connecting the Network Cable Connection to Switched OutletsConnecting a Local PC Connecting an External ModemSystem Mode and User Mode ConfigurationAccessing the Web Browser Interface Accessing the Text Interface $ telnet 192.168.168.168 Enter Configuration Menus General Parameters Menu Web Browser Interface General Parameters MenusGeneral Parameters Menu Text Interface IPS-800/IPS-1600 Series User’s Guide Serial Parameters Serial Parameters MenuIPS-800/IPS-1600 Series User’s Guide Plug Parameters Menu Web Browser Interface Plug Parameters MenusPlug Passwords and Co-Location Features Reboot Cycles Network Parameters Network Parameters MenusConfiguration IP Security Feature Configuration 12 Telnet Parameters Menu Web Browser Interface Telnet Parameters Menus14 Web Server Parameters Menu Web Browser Interface Web Server Parameters MenusSave Configuration Parameters Plug Status Screen Web Browser Interface OperationOperation via the Web Browser Interface Plug Status Menu Web Browser Interface IPS-800 Shown Plug Status Screen Text Interface Operation via the Text InterfaceOn 1 or /ON Router Boot/On/Off Commands Text InterfaceOFF 2 or /OF Router Applying Commands to Several Plugs Text InterfaceAutomated Mode Logging Out of Command ModeOperation Manual Operation Sending Parameters to a File Saving and Restoring Configuration ParametersRestoring Saved Parameters Upgrading the IPS Firmware IPS-800/IPS-1600 Series User’s Guide Apx-1 Interface DescriptionSerial COM / RS232 Port Interface Apx-2 SpecificationsApx-3 Customer ServiceApx-4 Trademark and Copyright InformationIndex-1 IndexIndex-2 IPS-4 Internet Power Switch User’s GuidePage IPS-800/IPS-1600 Series User’s Guide Page Sterling Irvine California 949 586-9950 Toll Free
Top Page Image Contents