Western Telematic MT5634 manual Command P Pulse Dialing, Command Qn Result Codes Enable/Disable

Page 12

MT5634 Modem; AT Command Set

Command: P	Pulse Dialing
Values:	P, T
Default:	T
Description:	Conﬁgures the modem for pulse (non-touch-tone) dialing. Dialed
	digits are pulsed until a T command or dial modiﬁer is received.

Command: Qn	Result Codes Enable/Disable
Values:	n = 0 or 1
Default:	0
Description:	Q0	Enable result codes.
	Q1	Disable result codes.
	Q2	Returns an OK for backward compatibility with
		some software.

Command: Sr=n	Set Register Value
Values:	r = S-register number; n varies
Default:	None
Description:	Set value of register Sr to value of n, where n is entered in
	decimal format (e.g., S0=1).

Command: Sr?	Read Register Value
Values:	r = S-register number
Default:	None
Description:	Read value of register Sr and display it in 3-digit decimal form
	(e.g., S2? gives the response 043).

Command: T	Tone Dialing
Values:	P, T
Default:	T
Description:	Conﬁgures the modem for DTMF (touch-tone) dialing. Dialed
	digits are tone dialed until a P command or dial modiﬁer
	is received.

Command: Vn	Result Code Format
Values:	n = 0 or 1
Default:	1
Description:	V0	Displays result codes as digits (terse response).
	V1	Displays result codes as words (verbose response).

3-4

Image 12

Contents AT Command Set MT5634Page Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set AT Command Summary DescriptionAtmtsmodemcr AT Commands Command Ds Dial Command DS=y Dial Stored Telephone NumberCommand En Echo Command Mode Characters Command Fn Echo Online Data CharactersCommand H n Hook Control Command I n Information RequestCommand M n Monitor Speaker Mode Command N n Modulation HandshakeCommand P Pulse Dialing Command Qn Result Codes Enable/DisableCommand Sr=n Set Register Value Command Sr? Read Register ValueCommand Result Code Options Command Result Code SelectionCommand Zn Modem Reset Command Data Carrier Detect DCD ControlCommand &Dn Data Terminal Ready DTR Control Command &En XON/XOFF Pacing ControlCommand &Fn Load Factory Settings Command &Gn V.22bis Guard Tone ControlCommand Leased Line Operation Command Pulse Dial Make-to-Break Ratio SelectionCommand &Qn Asynchronous Communications Mode Command Data Set Ready DSR ControlCommand &Tn Loopback Test V.54 Test Commands Command &V Display Current SettingsCommand &Wn Store Current Conﬁguration Command &Zy=x Store Dialing CommandCommand \A n Command \B n Transmit BreakCommand \K n Break Control Command \Nn Error Correction Mode Selection Command \Qn Flow Control SelectionCommand \Tn Inactivity Timer Command \Vn Protocol Result CodeCommand \Xn XON/XOFF Pass-Through Command Data Calling ToneCommand %An Adaptive Answer Result Code Enable Command View Numbers in BlacklistCommand %DCn AT Command Control Command Fallback and Fall Forward ControlCommand %Hn Direct Connect Enable Command Cisco ConﬁgurationCommand $EB n Asynchronous Word Length Command $MB n Online BPS SpeedCommand $RP n Ring Priority vs. AT Command Priority Command $SB n Serial Port Baud RateCommand +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBF? Callback Failed Attempts Display Command #CBFR Callback Failed Attempts ResetCommand #CBIn Local Callback Inactivity Timer Command #CBNy=xCommand #CBSn Callback Enable/Disable Command #Pn Set 11-bit ParityCommand #Sx Enter Setup Password Command #S=x Store Setup PasswordRegister Unit Range Default Description RegistersS37 Decimal Registers MT5634 Modem AT Command Set Result Codes Terse Verbose DescriptionDelayed Remote Configuration and Country Code Configuration Example %%%ATMTSMODEMChanging the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free

Related manuals

Manual 36 pages 9.02 Kb