Western Telematic Official Manual for Modem: Comprehensive AT Command Guide

Page 23

 

 

AT Commands

Command: #CBF? Callback Failed Attempts Display

Values:

 

N/A

Default:

 

N/A

Description:

 

Requests the number of failed callback passwords since reset

 

 

or power-up. This number can be stored to nonvolatile memory

 

 

using the &W command.

Command:

#CBFR Callback Failed Attempts Reset

Values:

 

N/A

Default:

 

N/A

Description:

 

Resets the number of failed callback passwords to 0. This does

 

 

not reset the number stored in nonvolatile memory.

Command:

#CBIn

Local Callback Inactivity Timer

Values:

 

n = 1–255

Default:

 

20

Description:

 

Sets the time (in minutes) that the modem waits for a command

 

 

before forcing the user to enter the setup password again.

Command: #CBNy=x

 

 

Store Callback Password

Values:

 

y = 0–29

 

 

x = password

Defaults:

 

None

Description:

 

Sets the callback security password for the y memory location.

 

 

The password must have 6 to 10 characters, and cannot include

 

 

the + or - ¬characters.

Command:

#CBPn

Callback Parity

Values:

 

n = 0, 1, or 2

Default:

 

0

Description:

 

Sets parity for the callback security messages.

 

 

#CBP0 No parity.

 

 

#CBP1 Odd parity.

 

 

#CBP2 Even parity.

Command:

#CBRy

Callback Security Reset

Values:

 

y = 0–29

Default:

 

None

Description:

 

Clears the password and phone number in the y memory location.

3-15

Image 23
Contents MT5634 AT Command SetPage Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set Description AT Command SummaryAtmtsmodemcr AT Commands Command Fn Echo Online Data Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command En Echo Command Mode CharactersCommand N n Modulation Handshake Command H n Hook ControlCommand I n Information Request Command M n Monitor Speaker ModeCommand Sr? Read Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr=n Set Register ValueCommand Data Carrier Detect DCD Control Command Result Code OptionsCommand Result Code Selection Command Zn Modem ResetCommand &Gn V.22bis Guard Tone Control Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Fn Load Factory SettingsCommand Data Set Ready DSR Control Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command &Qn Asynchronous Communications ModeCommand &Zy=x Store Dialing Command Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Wn Store Current ConfigurationCommand \K n Break Control Command \A nCommand \B n Transmit Break Command \Vn Protocol Result Code Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Tn Inactivity TimerCommand View Numbers in Blacklist Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command %An Adaptive Answer Result Code EnableCommand Cisco Configuration Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command %Hn Direct Connect EnableCommand $SB n Serial Port Baud Rate Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $RP n Ring Priority vs. AT Command PriorityCommand #CBDn Callback Delay Command +VDR=x, y Distinctive Ring ReportCommand #CBAn Callback Attempts Command #CBNy=x Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBIn Local Callback Inactivity TimerCommand #S=x Store Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #Sx Enter Setup PasswordRegisters Register Unit Range Default DescriptionS37 Decimal Registers MT5634 Modem AT Command Set Terse Verbose Description Result CodesDelayed Example %%%ATMTSMODEM Remote Configuration and Country Code ConfigurationChanging the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free
Related manuals
Manual 36 pages 9.02 Kb