Western Telematic MT5634 manual Remote Configuration and Country Code Configuration

Page 31

6.Remote Configuration and Country Code Configuration

6.1. Remote Configuration

Remote configuration is a network management tool that allows you to configure modems anywhere in your network from one location. With password-protected remote configuration, you can issue AT commands to a remote modem for maintenance or troubleshooting as if you were on-site.

6.1.1.Basic Procedure

The following steps are valid regardless of whether the connection is established by the local or the remote modem.

1.Establish a data connection with a remote modem.

2.Send three remote configuration escape characters followed by AT and the setup password and press [Enter].

Example: %%%ATMTSMODEM.

You have four tries to enter the correct password before being disconnected. If the password is correct, the remote modem responds with OK.

3.You can now send AT commands to configure the remote modem.

4.When you have finished configuring the remote modem, save the new configuration by typing AT&W0. Press [Enter].

5.Type ATO. Press [Enter] to exit remote configuration. You can now break the connection.

6.1.2.Setup

MT5634 Modems are shipped with a default setup password (MTSMODEM). Because anyone who has the User Guide knows the default setup password, you should change the password and possibly also the remote configuration escape character.

6-1

Image 31
Contents MT5634 AT Command SetPage Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set Description AT Command SummaryAtmtsmodemcr AT Commands Command Fn Echo Online Data Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command En Echo Command Mode CharactersCommand N n Modulation Handshake Command H n Hook ControlCommand I n Information Request Command M n Monitor Speaker ModeCommand Sr? Read Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr=n Set Register ValueCommand Data Carrier Detect DCD Control Command Result Code OptionsCommand Result Code Selection Command Zn Modem ResetCommand &Gn V.22bis Guard Tone Control Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Fn Load Factory SettingsCommand Data Set Ready DSR Control Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command &Qn Asynchronous Communications ModeCommand &Zy=x Store Dialing Command Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Wn Store Current ConfigurationCommand \B n Transmit Break Command \A nCommand \K n Break Control Command \Vn Protocol Result Code Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Tn Inactivity TimerCommand View Numbers in Blacklist Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command %An Adaptive Answer Result Code EnableCommand Cisco Configuration Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command %Hn Direct Connect EnableCommand $SB n Serial Port Baud Rate Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $RP n Ring Priority vs. AT Command PriorityCommand #CBAn Callback Attempts Command +VDR=x, y Distinctive Ring ReportCommand #CBDn Callback Delay Command #CBNy=x Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBIn Local Callback Inactivity TimerCommand #S=x Store Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #Sx Enter Setup PasswordRegisters Register Unit Range Default DescriptionS37 Decimal Registers MT5634 Modem AT Command Set Terse Verbose Description Result CodesDelayed Example %%%ATMTSMODEM Remote Configuration and Country Code ConfigurationChanging the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free
Related manuals
Manual 36 pages 9.02 Kb