Western Telematic MT5634 manual AT Commands

Page 9

3. AT Commands

Command: AT	Attention Code
Values:	N/A
Description:	The attention code precedes all command lines except A/,
	A: and escape sequences.

Command:	[Enter] Key
Values:	N/A
Description:	Press the [Enter] (RETURN) key to execute most
	commands.

Command: A		Answer
Values:		N/A
Description:		Answer call before ﬁnal ring.
Command:	A/	Repeat Last Command
Values:		N/A
Description:		Repeat the last command string. Do not precede this
		command with AT. Do not press [Enter] to execute.
Command:	Bn	Communication Standard Setting
Values:		n = 0–3, 15, 16
Default:		0 and 15
Description:		B0	Select ITU-T V.22 mode when modem is at 1200 bps.
		B1	Select Bell 212A when modem is at 1200 bps.
		B2	Deselect V.23 reverse channel (same as B3).
		B3	Deselect V.23 reverse channel (same as B2).
		B15	Select V.21 when the modem is at 300 bps.
		B16	Select Bell 103J when the modem is at 300 bps.

3-1

Image 9

Contents MT5634 AT Command SetPage Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set Description AT Command SummaryAtmtsmodemcr AT Commands Command DS=y Dial Stored Telephone Number Command Ds DialCommand En Echo Command Mode Characters Command Fn Echo Online Data CharactersCommand I n Information Request Command H n Hook ControlCommand M n Monitor Speaker Mode Command N n Modulation HandshakeCommand Qn Result Codes Enable/Disable Command P Pulse DialingCommand Sr=n Set Register Value Command Sr? Read Register ValueCommand Result Code Selection Command Result Code OptionsCommand Zn Modem Reset Command Data Carrier Detect DCD ControlCommand &En XON/XOFF Pacing Control Command &Dn Data Terminal Ready DTR ControlCommand &Fn Load Factory Settings Command &Gn V.22bis Guard Tone ControlCommand Pulse Dial Make-to-Break Ratio Selection Command Leased Line OperationCommand &Qn Asynchronous Communications Mode Command Data Set Ready DSR ControlCommand &V Display Current Settings Command &Tn Loopback Test V.54 Test CommandsCommand &Wn Store Current Conﬁguration Command &Zy=x Store Dialing CommandCommand \A n Command \B n Transmit BreakCommand \K n Break Control Command \Qn Flow Control Selection Command \Nn Error Correction Mode SelectionCommand \Tn Inactivity Timer Command \Vn Protocol Result CodeCommand Data Calling Tone Command \Xn XON/XOFF Pass-ThroughCommand %An Adaptive Answer Result Code Enable Command View Numbers in BlacklistCommand Fallback and Fall Forward Control Command %DCn AT Command ControlCommand %Hn Direct Connect Enable Command Cisco ConﬁgurationCommand $MB n Online BPS Speed Command $EB n Asynchronous Word LengthCommand $RP n Ring Priority vs. AT Command Priority Command $SB n Serial Port Baud RateCommand +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBFR Callback Failed Attempts Reset Command #CBF? Callback Failed Attempts DisplayCommand #CBIn Local Callback Inactivity Timer Command #CBNy=xCommand #Pn Set 11-bit Parity Command #CBSn Callback Enable/DisableCommand #Sx Enter Setup Password Command #S=x Store Setup PasswordRegisters Register Unit Range Default DescriptionS37 Decimal Registers MT5634 Modem AT Command Set Terse Verbose Description Result CodesDelayed Example %%%ATMTSMODEM Remote Configuration and Country Code ConfigurationChanging the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free

Related manuals

Manual 36 pages 9.02 Kb

3. AT Commands

Command:

Repeat Last Command

Command:

Communication Standard Setting