Tyan Computer Thunder i7505, S2665 warranty Bios Setup Utility, Main, To select an item

Page 25

Chapter 3: BIOS

3.0 – BIOS Setup Utility

With the BIOS setup utility, you can modify BIOS settings and control the special features of your computer. The setup utility uses a number of menus for making changes and turning the special features on or off.

NOTE

All menus are based on a typical system. The actual menus displayed on your screen may be different and depend on the hardware and features installed in your computer.

 

To start the BIOS setup utility:

 

 

 

 

 

 

 

a.

Turn on or reboot your system

 

 

 

 

 

 

b.

Press <F2> to start BIOS setup utility

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BIOS Setup Utility

 

 

 

 

Main

 

Advanced

Security

Power

 

Boot

Exit

 

BIOS Version

 

1.00.x x

 

 

 

Item Specific Help

 

 

 

 

 

<Tab>, <Shift-Tab>, or

 

 

 

 

 

 

 

 

 

Enable ACPI

 

 

[Enabled]

 

 

 

<Enter> selects field

 

Installed OS

 

 

[Win2000/XP]

 

 

 

 

 

Reset Configuration Data

[Yes]

 

 

 

 

 

 

System Time

 

[12:59:59]

 

 

 

 

 

System Date

 

 

[11/01/2002]

 

 

 

 

 

NumLock

 

 

[Enabled]

 

 

 

 

 

 

System Information

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1 Help

Select Item

-/+ Change Values

4Sub- Menu

F9 Setup Defaults

 

 

ESC Exit

Select Menu

Enter Select

F10 Save and Exit

 

 

 

 

 

 

 

 

 

 

 

To select an item

Use the left/right () arrow keys to make a selection

To display a sub-menu(A pointer “ 4” marks all sub menus)

Use the arrow keys to move the cursor to the sub menu you want. Then press <Enter>.

25

http://www.TYAN.com

Image 25
Contents Thunder S2665 Table of Contents Before you begin… Check the box contents Introduction BiosIntegrated I/O Integrated PCI IDESystem Management Form FactorInstallation Board InstallationHow to install our products right….the first time Do not Apply Power to the Board if IT has Been DamagedBoard Page Close Pin-1 and Pin-2 Default Jumper and Connector Settings FunctionClose Pin-1 and Pin-2 Default J65 J11Enable/Disable Onboard LAN Jumper J10 J16 CD Audio connectorFan Connectors J11, J19, J22, J32, J38, J55 and J60 ClosePin-3 Close Pins 2 PS/2 Acpi Jumper J12 Pin-3 Close Pins 1 and 2 DefaultFlashing Bios Protection Jumper J13 Disable Slot-B and Slot- C PCI- X Capa bility Jumper J31 Disable Slot-A PCI-X Capability Jumper J30Clear CM OS Jumper J50 Default Ieee 1394 Connector J66 Pin-1 Close Pins 2LCD Connector J69 GND VCCOEM Reserved Connectors and Jumpers Front Panel Connector J74 Signal Description Pin #Scsi RAID PCI Slot-C Mounting the Motherboard Installing the MemoryMemory Installation Procedure Reminder Installing the Processors and HeatsinksPage Installing Add- In Cards Finishing Installing the HeatsinkSpdif Spdif RCA connector Connecting External DevicesRJ45 LAN Port Ieee Ieee 1394 connector Audio Port Line In JackInstalling the Power Supply Attaching IDE and Floppy Drive Cables Finishing Up Bios Setup Utility BiosMain To select an itemBios Legend Bar Bios Menu BarKey Function Enable Acpi Sub-Menu Feature Bios Main MenuInstall OS Sub-Menu Feature Win2000/XP Reset Configuration Data Sub-Menu FeatureProcessors Sub-Menu Feature Option Description Bios Advanced MenuEnabled Chipset Sub-Menu Feature Option DescriptionECP IRQ4IRQ7 DMA3PCI Device Slot n Sub-Menu Feature Option Description AGP Slot Sub-Menu Feature Option Description128Mb Bios Power Menu Bios Security MenuPower Remote Power -On Sub-Menu Feature Option DescriptionAGP Load Setup Defaults Bios Exit MenuExit Exit Saving ChangesCPU, Memory, Video Beep Codes DiagnosticsFlash Utility Appendix I Glossary Page Page Page Technical Support Returning Merchandise for ServiceDocument # D1491