Tyan Computer S2665, Thunder i7505 warranty Document # D1491

Page 40

Notice for the USA

Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15: This device complies with part 15 of the FCC Rule s

Operation is subject to the following conditions:

1)This device may not cause harmful interference, and

2)This device must accept any interference received including interference that may cause undesired operation. If this equipment does cause harmful int erference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Plug the equipment into an outlet on a circuit different from that of the receiver.

Consult the dealer on an experienced radio/television technician for help.

Notice for Canada

This apparatus complies with the Class B limits for radio interference as specified in the Canadian Department of Communications Radio Interference Regulations. (Cet appareil est conforme aux norms de Classe B d’interference radio tel que specifie par le Ministere Canadien des Communications dans les reglements d’ineteference radio.)

Notice for Europe (CE Mark)

This product is in conformity with the Council Directive 89/336/EEC, 92/31/EEC (EMC).

CAUTION: Lithium battery included with this board. Do not puncture, mutilate, or dispose of battery in fire. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by manufacturer. Dispose of used battery according to manufacturer instructions and in accordance with your local regulations.

Document # : D1491 - 100

40

http://www.tyan.com

Image 40
Contents Thunder S2665 Table of Contents Before you begin… Check the box contents Bios IntroductionIntegrated PCI IDE Integrated I/OSystem Management Form FactorBoard Installation InstallationHow to install our products right….the first time Do not Apply Power to the Board if IT has Been DamagedBoard Page Jumper and Connector Settings Function Close Pin-1 and Pin-2 DefaultClose Pin-1 and Pin-2 Default J65 J11J16 CD Audio connector Enable/Disable Onboard LAN Jumper J10Fan Connectors J11, J19, J22, J32, J38, J55 and J60 ClosePin-3 Close Pins 2 PS/2 Acpi Jumper J12 Pin-3 Close Pins 1 and 2 DefaultFlashing Bios Protection Jumper J13 Disable Slot-B and Slot- C PCI- X Capa bility Jumper J31 Disable Slot-A PCI-X Capability Jumper J30Clear CM OS Jumper J50 Default Ieee 1394 Connector J66 Pin-1 Close Pins 2LCD Connector J69 VCC GNDOEM Reserved Connectors and Jumpers Front Panel Connector J74 Signal Description Pin #Scsi RAID PCI Slot-C Installing the Memory Mounting the MotherboardMemory Installation Procedure Installing the Processors and Heatsinks ReminderPage Finishing Installing the Heatsink Installing Add- In CardsConnecting External Devices Spdif Spdif RCA connectorRJ45 LAN Port Ieee Ieee 1394 connector Audio Port Line In JackInstalling the Power Supply Attaching IDE and Floppy Drive Cables Finishing Up Bios Bios Setup UtilityMain To select an itemBios Legend Bar Bios Menu BarKey Function Bios Main Menu Enable Acpi Sub-Menu FeatureInstall OS Sub-Menu Feature Win2000/XP Reset Configuration Data Sub-Menu FeatureBios Advanced Menu Processors Sub-Menu Feature Option DescriptionEnabled Chipset Sub-Menu Feature Option DescriptionIRQ4 ECPIRQ7 DMA3PCI Device Slot n Sub-Menu Feature Option Description AGP Slot Sub-Menu Feature Option Description128Mb Bios Security Menu Bios Power MenuPower Remote Power -On Sub-Menu Feature Option DescriptionAGP Bios Exit Menu Load Setup DefaultsExit Exit Saving ChangesCPU, Memory, Video Beep Codes DiagnosticsFlash Utility Appendix I Glossary Page Page Page Returning Merchandise for Service Technical SupportDocument # D1491