Omron DR 170 14 manual Klinkmann Automation Omron Ethernet DAServer

Page 24

Klinkmann Automation Omron Ethernet DAServer

22

This configuration view has 15 parameters (configuration requires proven network information, it can not be validated by the DAServer):

•Enter Controller’s Network Address - to each network in the OMRON system can be assigned an unique network address between 0 and 127. When communicating with a node on another (remote) network, the entered value must be consistent with the network address (non-zero) assigned in the routing tables. The network address of 0 indicates the local network. Note: The default Network Address is 0.

•Enter Controller’s Node Address - each OMRON Controller in Ethernet network must have its own unique node address between 1 and 126 (if Controller is inter- networked via other OMRON FA network then Node Address can have different range. For example, if inter-networked via SYSMAC LINK network, the Node Address range is between 1 and 62. Care should be taken to select a node address that will not conflict with other devices in the system.

Note: If destination node is OMRON PLC with Ethernet Unit installed then Controller Node Address must be configured according to following rules:

-if automatic conversion of Ethernet Unit’s IP address is used (also the node number setting rotary switch on the front panel of the Ethernet Unit is used) then Controller Node Address must be equal with the fourth byte (octet) of local IP address of Ethernet Unit;

-if automatic conversion of Ethernet Unit’s IP address is not used (IP Address Table is used) then Controller Node Address must be equal with the Node number configured in the Ethernet Unit’s IP Address Table.

•Enter Controller’s IP Address. The Controller’s IP Address must match with IP address configured at corresponding controller Ethernet Unit system setup.

•Enter Controller’s Port Number. Enter the UDP Port Number used for communications with this OMRON controller. The Port Number must much with the Port Number set in the OMRON controller by appropriate Ethernet Unit configuration software. Note: The default port number is 9600.

•Enter Computer’s Network Address - the Local Network Address: the unique network address between 1 and 127 is assigned to each OMRON Ethernet network in the system. The entered value must be consistent with the network address assigned in the routing tables. When communicate only with nodes in the local network, you can set this Address to zero (default value).

•Select the Controller Series. The available series are: CS1/CJ1, C200HX/HG/HE, CV-series, C/CPM2X and CQM1. To select Controller Series, click on the combo box button and make your choice from the list. Note: Only PLCs of CS1/CJ1, C200HX/HG/HE and CV series are directly accessible in Ethernet network. All other series PLCs must be inter-networked to get data from them.

•Select Controller type. To select Controller type, click on the combo box button and make your choice from the list. The available types depends on selection in Controller Series combo box: CS1/CJ1 series offers 2 options (CS1 and CJ1), C200HX/HG/HE series offers one option (C200HX/HG/HE), CV-series offers 5 options (CV500, CVM1-CPU01-E, CV1000, CV2000 and CVM1-CPU11-E),

Omron Ethernet DAServer Ver 1.x User Manual Rev 1.3

17014m13

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Omron Ethernet Direct DAServer User’s Guide Ver 1.x Rev DR 170Contents Contents About This User GuideIndex Introduction OverviewCommunication Protocols Application Communications ProtocolsSuiteLink Accessing Items via the DAServer Fins Message CommunicationFastDDE NetDDEDDE/SuiteLink Features Demo ModeBefore starting the Omron Ethernet DAServer Ethernet Unit Configuration Example for CS1 PLC Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Comments on example program ladder diagram Example program for sending unsolicited data from PLCKlinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Getting Started Quickly with the DAServer To prepare the Omron Ethernet DAServerConfiguring the DAServer NewSOCKET000 by defaultAdd Controller Object To prepare the Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer To create Socket objects from the Configuration branch DASOmronEth Hierarchy in the DAServer ManagerHost Name IP Addr Port NumberTo add Controller to your Omron Ethernet hierarchy Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Configuring Device Group Definitions Device Group DefinitionsTo create or add device groups To make edits on device groups To configure default update intervals To delete device groupsTo edit update intervals Archiving Configuration SetsTo archive configuration sets Scan-Based Message HandlingConfiguring Device Item Definitions To use different configuration sets from the current oneDevice Item Definitions Name Item ReferenceTo create or add device items To add item referencesTo rename a device item from the list To delete a device item from the listHot Configuration To export device itemsTo import device items Item Name General Format PnSPnb or Pnbb or Pn.b or Pn.bb Pn-PhSBCD Format Long Format Signed/BCDFloating Point Format IEEE/BCD Ascii Strings FormatRead WriteImortant Note CS1/CJ1 PLCs = a To M= a Klinkmann Automation Omron Ethernet DAServer C200HX/C200HG/C200HE PLCs CV-series PLCs PVS Flag or Bit Status Step StatusCPM2x PLCs Klinkmann Automation Omron Ethernet DAServer CQM1 PLCs DAServer Standard System Items System Item Type Description Values Name Access Rights DAServer Global System ItemDAServer Device-Specific System Items Klinkmann Automation Omron Ethernet DAServer DAServer Device-Group-Specific System Items RangeRange Generic OPC Syntax AREA10.VESSEL1.TIC1.PLC.D100YourOPCAccessPath.$SYS$Status Monitoring Connectivity Status with the PLC=DASOmronEthPLC!$SYS$Status Using DDEStatus and IOStatus in Excel Monitoring the Status of DAS ConversationsReading Values from the DAServer into Excel Writing Values to the DAServer from Excel Channel=INITIATEapplicationname,topicname=POKEchannel,itemname, DataReference =TERMINATEchannelError Messages and Codes DAServer Error MessagesError Message Explanation Probable Cause Solution Log Flag Item Names Creating write Invalid value poked Check Item’s DASProtFail Data, received Take into DASProtWarn Server-Specific Error Codes Error code Logger Message Log FlagFins Response Codes Main Code Sub Probable Cause Remedy Log Flag HexKlinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer DAServer Architecture DAServersPlug-ins DAS EnginePLC Protocol Layer Component Environments Klinkmann Automation
Related manuals
Manual 70 pages 30.48 Kb

DR 170 14 specifications

The Omron DR 170 14 is a leading-edge digital infrared thermometer that has established a strong reputation for its accuracy and efficiency in measuring body temperature. This advanced device is particularly noted for its user-friendly design, making it suitable for both medical professionals and home use.

One of the key features of the Omron DR 170 14 is its non-contact measurement capability, allowing users to obtain temperature readings from a distance of about 1-3 centimeters. This feature is crucial in minimizing the risk of cross-contamination, especially in healthcare settings. The thermometer utilizes infrared technology to detect the infrared energy emitted by the body, ensuring quick and reliable readings in just seconds.

The Omron DR 170 14 also boasts a large, easy-to-read LCD display that provides clear visibility of temperature readings. This display is backlit, allowing for usage in low-light conditions, making it convenient during nighttime monitoring of children's temperatures.

Furthermore, the device includes a memory function that can store multiple temperature readings, assisting users in tracking fever patterns over time. This feature is invaluable for caregivers and healthcare providers as it allows for better assessment and decision-making regarding treatment plans.

In terms of accuracy, the Omron DR 170 14 is equipped with advanced measurement algorithms that enhance precision in readings, positioning it as a reliable option for temperature measurement. The thermometer can measure not only body temperature but also surface temperatures of objects and liquids, providing versatility beyond just clinical settings.

Another notable characteristic is its compact and lightweight design, which makes it highly portable and easy to carry around, whether in a medical bag or a home setting. The thermometer is also powered by batteries, ensuring that it remains operational even in case of power outages.

Overall, the Omron DR 170 14 stands out for its combination of modern technology, ease of use, and reliable performance. With its non-contact functionality, rapid readings, and memory features, it serves as an essential tool for anyone needing accurate temperature assessments, whether in a clinical or home environment. The thermometer exemplifies Omron's commitment to creating healthcare solutions that are not only innovative but also accessible to a wide range of users.
Top Page Image Contents