Omron DR 170 14 manual Klinkmann Automation Omron Ethernet DAServer

Page 60

Klinkmann Automation Omron Ethernet DAServer

58

 

 

number too large.

number below the

 

 

 

 

maximum node number.

 

 

 

 

 

 

 

03

Send error caused by

Reduce the traffic on the

DASProtFail

 

 

lack of available space

Ethernet Unit. Check

 

 

 

in PLC internal buffers.

user application.

 

 

 

 

 

 

 

05

Node number setting

Make sure the node

DASProtFail

 

 

error.

number is within

 

 

 

 

specified range and that

 

 

 

 

there are no duplicate

 

 

 

 

node numbers.

 

 

 

 

 

 

06

Node number duplication error.

Make sure that there are DASProtFail no duplicate node

numbers.

02:Remote 01 node error

IP address of remote node was not set correctly in IP address table or IP router table.

Set IP address of remote node into IP address table, and, if internetwork transmission is required, into IP router table.

DASProtFail

 

02

No node with the

Check the remote

DASProtFail

 

 

specified unit address.

node’s unit address and

 

 

 

 

make sure the correct

 

 

 

 

one is being used in the

 

 

 

 

control data.

 

 

 

 

 

 

 

05

Message packet was

Check the protocol and

DASProtFail

 

 

corrupted by

controller status by

 

 

 

transmission error or

reading them with FINS

 

 

 

response time-out

commands. Increase the

 

 

 

(response watchdog

number of transmit retry

 

 

 

timer interval too short)

attempts.

 

 

 

or transmission frame

Increase the value for

 

 

 

corrupted or PLC

the response monitor

 

 

 

internal reception buffer

time in the control data.

 

 

 

full.

Read out the error log

 

 

 

 

and correct as required.

 

 

 

 

 

 

03:

01

Error occured in the

Take corrective action,

DASProtFail

Communic.

 

communications

referring to

 

Controller

 

controler. ERC

troubleshooting

 

error

 

indicator is lit.

procedures in PLC

 

 

 

 

manual.

 

 

 

 

 

 

 

02

CPU error occured in

Check the CPU

DASProtFail

 

 

the PC at the

indicators at remote PLC

 

 

 

destination node.

and clear the error in the

 

 

 

 

CPU (refer to the PLC’s

 

 

 

 

 

 

Omron Ethernet DAServer Ver 1.x User Manual Rev 1.3

17014m13

Image 60
Contents Omron Ethernet Direct DAServer User’s Guide Ver 1.x Rev DR 170Contents Contents About This User GuideIndex Introduction OverviewCommunication Protocols Application Communications ProtocolsSuiteLink Accessing Items via the DAServer Fins Message CommunicationFastDDE NetDDEDDE/SuiteLink Features Demo ModeBefore starting the Omron Ethernet DAServer Ethernet Unit Configuration Example for CS1 PLC Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Comments on example program ladder diagram Example program for sending unsolicited data from PLCKlinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Getting Started Quickly with the DAServer To prepare the Omron Ethernet DAServerConfiguring the DAServer NewSOCKET000 by defaultAdd Controller Object To prepare the Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer To create Socket objects from the Configuration branch DASOmronEth Hierarchy in the DAServer ManagerHost Name IP Addr Port NumberTo add Controller to your Omron Ethernet hierarchy Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Configuring Device Group Definitions Device Group DefinitionsTo create or add device groups To make edits on device groups To configure default update intervals To delete device groupsTo edit update intervals Archiving Configuration SetsTo archive configuration sets Scan-Based Message HandlingConfiguring Device Item Definitions To use different configuration sets from the current oneDevice Item Definitions Name Item ReferenceTo create or add device items To add item referencesTo rename a device item from the list To delete a device item from the listHot Configuration To export device itemsTo import device items Item Name General Format PnSPnb or Pnbb or Pn.b or Pn.bb Pn-PhSBCD Format Long Format Signed/BCDFloating Point Format IEEE/BCD Ascii Strings FormatRead WriteImortant Note CS1/CJ1 PLCs = a To M= a Klinkmann Automation Omron Ethernet DAServer C200HX/C200HG/C200HE PLCs CV-series PLCs PVS Flag or Bit Status Step StatusCPM2x PLCs Klinkmann Automation Omron Ethernet DAServer CQM1 PLCs DAServer Standard System Items System Item Type Description Values Name Access Rights DAServer Global System ItemDAServer Device-Specific System Items Klinkmann Automation Omron Ethernet DAServer DAServer Device-Group-Specific System Items RangeRange Generic OPC Syntax AREA10.VESSEL1.TIC1.PLC.D100YourOPCAccessPath.$SYS$Status Monitoring Connectivity Status with the PLC=DASOmronEthPLC!$SYS$Status Using DDEStatus and IOStatus in Excel Monitoring the Status of DAS ConversationsReading Values from the DAServer into Excel Writing Values to the DAServer from Excel Channel=INITIATEapplicationname,topicname=POKEchannel,itemname, DataReference =TERMINATEchannelError Messages and Codes DAServer Error MessagesError Message Explanation Probable Cause Solution Log Flag Item Names Creating write Invalid value poked Check Item’s DASProtFail Data, received Take into DASProtWarn Server-Specific Error Codes Error code Logger Message Log FlagFins Response Codes Main Code Sub Probable Cause Remedy Log Flag HexKlinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer DAServer Architecture DAServersPlug-ins DAS EnginePLC Protocol Layer Component Environments Klinkmann Automation
Related manuals
Manual 70 pages 30.48 Kb

DR 170 14 specifications

The Omron DR 170 14 is a leading-edge digital infrared thermometer that has established a strong reputation for its accuracy and efficiency in measuring body temperature. This advanced device is particularly noted for its user-friendly design, making it suitable for both medical professionals and home use.

One of the key features of the Omron DR 170 14 is its non-contact measurement capability, allowing users to obtain temperature readings from a distance of about 1-3 centimeters. This feature is crucial in minimizing the risk of cross-contamination, especially in healthcare settings. The thermometer utilizes infrared technology to detect the infrared energy emitted by the body, ensuring quick and reliable readings in just seconds.

The Omron DR 170 14 also boasts a large, easy-to-read LCD display that provides clear visibility of temperature readings. This display is backlit, allowing for usage in low-light conditions, making it convenient during nighttime monitoring of children's temperatures.

Furthermore, the device includes a memory function that can store multiple temperature readings, assisting users in tracking fever patterns over time. This feature is invaluable for caregivers and healthcare providers as it allows for better assessment and decision-making regarding treatment plans.

In terms of accuracy, the Omron DR 170 14 is equipped with advanced measurement algorithms that enhance precision in readings, positioning it as a reliable option for temperature measurement. The thermometer can measure not only body temperature but also surface temperatures of objects and liquids, providing versatility beyond just clinical settings.

Another notable characteristic is its compact and lightweight design, which makes it highly portable and easy to carry around, whether in a medical bag or a home setting. The thermometer is also powered by batteries, ensuring that it remains operational even in case of power outages.

Overall, the Omron DR 170 14 stands out for its combination of modern technology, ease of use, and reliable performance. With its non-contact functionality, rapid readings, and memory features, it serves as an essential tool for anyone needing accurate temperature assessments, whether in a clinical or home environment. The thermometer exemplifies Omron's commitment to creating healthcare solutions that are not only innovative but also accessible to a wide range of users.