Omega Speaker Systems VR200 Setting the Unit, Setting the Waveform Span Rate TIME/DIV

Page 16

2.2 Program Set Commands

2.2.4 Setting the Unit

(See Section 4.3 of the instruction manual for the VR200.)

Format: SNp1, p2

p1:

Channel number (CC)

p2:

Engineering unit (up to six characters)

Example: SN02, kg

This example assigns the unit “kg” to channel 2. Note that a unit can only be assigned to channels of the SCL or SQRT input.

2.2.5 Setting the Waveform Span Rate (TIME/DIV)

(See Section 4.4 of the instruction manual for the VR200.)

Format: SWp1

 

p1:

Select the waveform span rate from 1, 5, 10, 20, 30, and 60

 

(minutes).

Example: SW1

This example sets the waveform span rate to 1 minute.

2.2.6 Setting the Clock

(See Section 4.5 of the instruction manual for the VR200.)

Format: SDp1, p2

p1:

Date (YY/MM/DD)

 

YY: The last two digits of the Western year

 

MM: 01 to 12

 

DD: 01 to 31

p2:

Time (HH:MM:SS)

 

HH: 00 to 23

 

MM: 00 to 59

 

SS: 00 to 59

Example: SD96/03/13, 15:02:00

2.2.7 Copying the Channel Settings

(See Section 4.6 of the instruction manual for the VR200.)

Format: SYp1, p2

p1:

Channel number (CC) from which you want to copy the settings

 

(origin)

p2:

Channel number (CC) to which you want to copy the settings

 

(destination)

Example: SY01, 03

This example copies all settings from channel 1 to channel 3.

Note

You can only copy from a lower channel number to a higher channel number.

2 RECEIVING FUNCTIONS

2 - 5

Image 16
Contents User’sGuide Servicing North America Preface TrademarksContents Transmitting Functions Time Chart Initial Status Errors During RS-422-A OutputProgram Examples Installing the RS-422-A Interface Interface SpecificationsInterface Terminal Terminal Assignment Cable TerminationCommunication Wiring Data ConfigurationStart-stop Asynchronous Communication TextInput Buffer Buffer OverflowSetting up the RS-422-A Communication Interface Setup ProcedureParameters IdentifierTerminator List of Program Set Commands Setting the Range and ScaleFormat SRp1,mode Example SR01,SKIPExample SR01, DI, Format SRp1, mode, p2Format SRp1, mode, p2, p3, p4, p5, p6, p7, p8 Setting Alarms Setting the Unit Setting the Waveform Span Rate TIME/DIVSetting the Clock Copying the Channel SettingsSetting the Partial Expanded Display Setting the Discrete Zone DisplaySetting the Tag Setting the Trip Level Setting the Data File Name FileSetting the LCD Brightness and LCD Saver LCD Setting the Summer/ Winter Time DSTFormat MDp1, p2, p3 Example MD02, ON, onList of Program Control Commands Alarm AcknowledgeStandard Screen Call Initializing the Data MemoryLoading the SET Configuration File Saving the SET Configuration FileSelecting the Output Data Selecting the Output Format for Measured DataMessage Writingfor the VR 200 with style number 2 or higher Status Output Execution of TriggerRequests for the data to be prepared in the buffer Open Command Close CommandESC O Crlf ESC C CrlfIntroduction to Output Data Formats Sequence see also Sections 2.3.7Output Format of Measured Values in Ascii Mode Output Data FormatsOutput Format of Measured Values in Binary Mode Output Format of Parameter Settings Output Format of Unit and Decimal Point Information Time Chart Initial Status Preventing Errors OutputHow to Request Error Message Output ESC S CR LFTiming of Resetting the Error Status Program Examples EnvironmentOpen TEST.DAT for Input AS #2 Others LF is sent automatically 210 ‘ 220 ‘ Open COM11200,N,8,1,LF AS #1 Print a Appendix Appendix 1 Ascii Code TableAppendix 2 File Naming Rules File Name LengthLowercase/Uppercase Letters System-reserved File NamesIndex Index for Command Reference Warrant Y/ Disclaimer Temperature