NETGEAR FVX538NA Restoring the Default Configuration and Password, Problems with Date and Time

Page 185

ProSafe VPN Firewall 200 FVX538 Reference Manual

Restoring the Default Configuration and Password

This section explains how to restore the factory default configuration settings, changing the firewall’s administration password to password and the IP address to 192.168.1.1. You can erase the current configuration and restore factory defaults in two ways:

•Use the Erase function of the firewall (see “Backup and Restore Settings” on page 6-14).

•Use the reset button on the rear panel of the firewall. Use this method for cases when the administration password or IP address is not known.

To restore the factory default configuration settings without knowing the administration password or IP address, you must use the reset button on the rear panel of the firewall.

To restore the factory defaults:

1.Press and hold the reset button until the Test LED turns on and begins to blink (about 10 seconds).

2.Release the reset button and wait for the firewall to reboot.

Problems with Date and Time

The E-Mail menu in the Content Filtering section displays the current date and time of day. The VPN firewall uses the Network Time Protocol (NTP) to obtain the current time from one of several Network Time Servers on the Internet. Each entry in the log is stamped with the date and time of day. Problems with the date and time function can include:

•Date shown is January 1, 2000. Cause: The firewall has not yet successfully reached a Network Time Server. Check that your Internet access settings are configured correctly. If you have just completed configuring the firewall, wait at least five minutes and check the date and time again.

•Time is off by one hour. Cause: The firewall does not automatically sense Daylight Savings Time. Check the Time Zone menu, and check or uncheck the box marked “Adjust for Daylight Savings Time”.

Troubleshooting

7-7

v1.0, August 2006

Image 185

Contents ProSafe VPN Firewall FVX538 Reference Manual Statement of Conditions TrademarksEU Regulatory Compliance Statement Bestätigung des Herstellers/ImporteursAdditional Copyrights Voluntary Control Council for Interference Vcci StatementAugust MD5 Product and Publication Details Contents Chapter LAN Configuration Chapter Virtual Private Networking Chapter Router and Network Management Chapter Troubleshooting Index Conventions, Formats and Scope About This ManualHow to Print this Manual How to Use This ManualRevision History Xvi Chapter Introduction Key FeaturesPowerful, True Firewall with Content Filtering Extensive Protocol Support Security FeaturesAutosensing Ethernet Connections with Auto Uplink Trend Micro Integration Easy Installation and ManagementPackage Contents Object Descriptions Router Front PanelWAN Router Rear Panel Rack Mounting Hardware Router’s IP Address, Login Name, and PasswordEnter http//192.168.1.1 as the URL Default Log In SettingsProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual Logging into the VPN Firewall Connecting the FVX538 to the InternetConfiguring the Internet Connections to Your ISPs Connection Method Data Required Internet connection methodsInternet connection methods Manually Configuring Your Internet Connection Setting the Router’s MAC AddressProSafe VPN Firewall 200 FVX538 Reference Manual Programming the Traffic Meter if Desired ProSafe VPN Firewall 200 FVX538 Reference Manual Parameter Description Traffic Meter SettingsConfiguring the WAN Mode Required for Dual WAN Setting Up Auto-Rollover Mode ProSafe VPN Firewall 200 FVX538 Reference Manual Setting Up Load Balancing ProSafe VPN Firewall 200 FVX538 Reference Manual Configuring Dynamic DNS If Needed ProSafe VPN Firewall 200 FVX538 Reference Manual Ddns links Configuring the Advanced WAN Options If Needed ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual Using the Firewall as a Dhcp server Chapter LAN ConfigurationConfiguring the LAN Setup Options ProSafe VPN Firewall 200 FVX538 Reference Manual Configuring Multi Home LAN IPs ProSafe VPN Firewall 200 FVX538 Reference Manual Creating the Network Database Managing Groups and Hosts LAN GroupsProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual Setting Up Address Reservation Check the Do you want to enable DMA Port? radio box Configuring and Enabling the DMZ PortProSafe VPN Firewall 200 FVX538 Reference Manual Static Routes Configuring Static RoutesRouting Information Protocol RIP ProSafe VPN Firewall 200 FVX538 Reference Manual Static Route Example Enabling Trend Micro Antivirus EnforcementProSafe VPN Firewall 200 FVX538 Reference Manual Click Apply to submit your changes ProSafe VPN Firewall 200 FVX538 Reference Manual Using Rules to Block or Allow Specific Kinds of Traffic About Firewall Protection and Content FilteringOutbound Rules Service Blocking Services-Based RulesOutbound Rules Services menu see Adding Customized Services onInbound Rules Port Forwarding Inbound Rules Inbound Rules Order of Precedence for Rules Setting LAN WAN RulesProSafe VPN Firewall 200 FVX538 Reference Manual LAN WAN Outbound Services Rules LAN WAN Inbound Services Rules Setting DMZ WAN RulesProSafe VPN Firewall 200 FVX538 Reference Manual Setting LAN DMZ Rules LAN DMZ Outbound Services Rules Attack Checks LAN DMZ Inbound Services RulesPptp LAN WAN Inbound Rule Hosting a Local Public Web Server Inbound Rules ExamplesProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual LAN WAN or DMZ WAN Inbound Rule Specifying an Exposed Host LAN WAN Outbound Rule Blocking Instant Messenger Outbound Rules ExampleAdding Customized Services ProSafe VPN Firewall 200 FVX538 Reference Manual Setting Quality of Service QoS Priorities Setting a Schedule to Block or Allow Specific Traffic Setting Block Sites Content Filtering ProSafe VPN Firewall 200 FVX538 Reference Manual Enabling Source MAC Filtering Port Triggering ProSafe VPN Firewall 200 FVX538 Reference Manual Outgoing Trigger Port Range fields Mail Notifications of Event Logs and Alerts ProSafe VPN Firewall 200 FVX538 Reference Manual Numerical Code Severity SysLog Facility Message LevelsInformational Informational messages Firewall Log Field Descriptions Administrator TipsProSafe VPN Firewall 200 FVX538 Reference Manual IP Addressing for VPNs in Dual WAN Port Systems Dual WAN Port SystemsRollover Mode Setup Screen Load Balancing Setup Screen Setting up a VPN Connection using the VPN Wizard Creating a VPN Tunnel to a Gateway ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual Creating a VPN Tunnel Connection to a VPN Client ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual IKE Policy VPN Tunnel PoliciesIKE Policy Table Managing IKE PoliciesManaging VPN Policies VPN PolicyVPN Policy Table VPN Tunnel Connection StatusCreating a VPN Gateway Connection Between FVX538 and FVS338 Configuring the FVX538ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual Configuring the FVS338 Creating a VPN Client Connection VPN Client to FVX538 Testing the ConnectionProSafe VPN Firewall 200 FVX538 Reference Manual Configuring the VPN Client Fvxlocal.com Home11.fvxremote.com ProSafe VPN Firewall 200 FVX538 Reference Manual Testing the Connection Certificate Authorities Generate Self Certificate Request, enter the required data Generating a Self Certificate RequestProSafe VPN Firewall 200 FVX538 Reference Manual Managing your Certificate Revocation List CRL Uploading a Trusted CertificateUpload Extended Authentication Xauth ConfigurationConfiguring Xauth for VPN Clients ProSafe VPN Firewall 200 FVX538 Reference Manual User Database Configuration Radius Client Configuration Enter the Primary Radius Server IP address Mode Config Operation Manually Assigning IP Addresses to Remote Users ModeConfigConfiguring the VPN Firewall ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual Configuring the ProSafe VPN Client for ModeConfig ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual ProSafe VPN Firewall 200 FVX538 Reference Manual Bandwidth Capacity Performance ManagementService Blocking VPN Firewall Features That Reduce TrafficProSafe VPN Firewall 200 FVX538 Reference Manual Source MAC Filtering Block SitesPort Forwarding VPN Firewall Features That Increase TrafficPort Triggering VPN Tunnels Using QoS to Shift the Traffic MixDMZ Port Tools for Traffic Management AdministrationChanging Passwords and Settings ProSafe VPN Firewall 200 FVX538 Reference Manual Check Allow Remote Management radio box Enabling Remote Management AccessHttps//134.177.0.1238080 Using a Snmp ManagerProSafe VPN Firewall 200 FVX538 Reference Manual Settings Backup and Firmware Upgrade Click default Backup and Restore SettingsRouter Upgrade To upgrade router software Setting the Time ZoneEnabling the Traffic Meter Monitoring the RouterProSafe VPN Firewall 200 FVX538 Reference Manual Setting Login Failures and Attacks Notification Monitoring Attached Devices IP Address Known PCs and DevicesPort Triggering Status data Viewing Port Triggering StatusRouter Status Fields Viewing Router Configuration and System StatusMonitoring WAN Ports Status Monitoring VPN Tunnel Connection Status VPN Status data VPN LogsDhcp Log Performing DiagnosticsDiagnostics Diagnostics ProSafe VPN Firewall 200 FVX538 Reference Manual Basic Functions Power LED Not OnLAN or Internet Port LEDs Not On Troubleshooting the Web Configuration InterfaceLEDs Never Turn Off ProSafe VPN Firewall 200 FVX538 Reference Manual Troubleshooting the ISP Connection Testing the LAN Path to Your Firewall Troubleshooting a TCP/IP Network Using a Ping UtilityPing -n 10 IP address Testing the Path from Your PC to a Remote DeviceProblems with Date and Time Restoring the Default Configuration and PasswordProSafe VPN Firewall 200 FVX538 Reference Manual Table A-1. VPN firewall Default Configuration Settings Appendix a Default Settings and Technical SpecificationsFeature Default Behavior Table A-2. VPN firewall Technical SpecificationsElectromagnetic Emissions ProSafe VPN Firewall 200 FVX538 Reference Manual Appendix B Related Documents ProSafe VPN Firewall 200 FVX538 Reference Manual What You Will Need to Do Before You Begin Appendix C Network Planning for Dual WAN PortsInternet Figure C-1Cabling and Computer Hardware Requirements Computer Network Configuration RequirementsInternet Configuration Requirements Where Do I Get the Internet Configuration Parameters? Internet Connection Information Form Virtual Private Networks VPNs Overview of the Planning ProcessInbound Traffic Dual WAN Ports Load Balancing PortsRequirements for exposed hosts in dual WAN port systems Inbound TrafficAlways change at the IP addresses Virtual Private Networks VPNs Reference Manual Road Warrior Example Dual WAN Ports, Before Rollover VPN Road Warrior Dual But a fully-qualified WAN1 or WAN2Road Warrior Example Dual WAN Ports, Load Balancing VPN Gateway-to-Gateway Single Gateway WAN PortsGateway-to-Gateway Example Single WAN Ports WAN A2to establish or re Gateway-to-Gateway Example Dual WAN Ports, Load Balancing NAT Router Remote tunnel Remote PC or WAN2 Index Index-2 Index-3 Index-4 Index-5 Index-6 Index-7 Index-8 Index-9 Index-10

Related manuals

Manual 2 pages 62.01 Kb

Manual 3 pages 5.38 Kb