NetComm 3G9W 54g Mode, 802.11b only mode, 54g Protection, Under most conditions, Preamble Type

Page 31

3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE

Option	Description

54g Mode	Select Auto mode for greatest compatibility. Select Performance mode for the fastest
	performance among 54g certified equipment. Select LRS mode if you are experiencing
	difficulty with legacy 802.11b equipment. If this does not work, you may also try
	802.11b only mode.

54g Protection	In Auto mode, the router will use RTS/CTS to improve 802.11g performance in mixed
	802.11g/802.11b networks. Turning protection Off will maximize 802.11g throughput
	under most conditions.

Preamble Type	Short preamble is intended for applications where maximum throughput is desired but
	it does not work with legacy equipment. Long preamble works with the current 1 and 2
	Mbit/s DSSS specification as described in IEEE Std 802.11-1999

Transmit Power	Set the power output (by percentage) as desired.

YML902 – 31

Image 31

Contents 3G9W Hspa 7.2 Mbps Wi-Fi Router Preface Important Notice and Safety PrecautionTable of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents FeaturesPowered off LED IndicatorsColor Mode Description Green Power on Off Power off LAN 1~4Rear Panel Rear panel contains the ports for data and power connectionsQuick Setup Save the router configuration and reboot see section Quick SetupSetup Procedure Configure the router through the Web User Interface WUIWeb User Interface Web User Interface Default SettingsDhcp Mode TCP/IP SettingsClick OK to submit the settings To login to the web interface, follow the steps below Login ProcedureBasic / Home Web User Interface HomepageFields Description Following table provides further details3G Settings 3G Service Setup 3G SettingsThis menu includes 3G service Setup and PIN Configuration 21 for instruction on how to fix this PIN Code Protection PIN ConfigurationPIN Lock Off YML902 PIN Code Change Wireless Wireless Option Description SetupSecurity Click Save/Apply to configure the wireless security optionsSelect Ssid Card. If the Ssid does not match, access is deniedAuthentication WEP Encryption will also be enabledConfiguration Point can be linked Broadcast and multicast messages. The default isDefault is disabled AP Isolation54g Protection 54g Mode802.11b only mode Mbit/s Dsss specification as described in Ieee StdCan be added Deny Rejects access for the specified MAC addressesMAC Filter MAC AddressClick Save/Apply to implement new configuration settings Wireless BridgeFeature Options Associated Authorized Lists those devices with authorized accessStation Info Is generated randomlyManagement Management Device SettingsRestore Default Update SettingsDefault screen upon successful installation Access Control YML902 Simple Network Time Protocol Sntp Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced SetupNo client subscribes to a multicast group Configuration ProtocolLocal Area Network LAN Igmp SnoopingPort Forwarding Network Address Translation NATExternal Port End Is selected the port ranges are automatically configuredSelected the port ranges are automatically configured Options DescriptionPort Triggering Open Port End Demilitarized DMZ HostTrigger Port End Trigger Protocol TCP, TCP/UDP or UDP Open Port StartSecurity Options Description User Name User-defined label for this restriction Parental ControlMAC address of the PC running the browser Routing YML902 YML902 Domain Name Servers DNS DNS Server ConfigurationOptions Descriptions Dynamic DNSStatus Status Test Description DiagnosticsSystem Log Click View System Log. The results are displayed as follows 3G Status Status Description Strongest cells Network Registration Status BCS Battery Charge LevelStatus Quality Ec/IoInterface Shows connection interfaces StatisticsService Shows the service type But may be needed by routing daemons RouteSelect Route to display the paths the Router has found Field DescriptionClick Dhcp to display the Dhcp information Dynamic Host Configuration Protocol DhcpARP Click ARP to display the ARP informationCLI commands Via Telnet Show all CLI commands CLI commands via TelnetRadio Signal Strength Reset/reboot deviceEnd the telnet session Connection status Radio BandImsi & Imei read Wireless LAN mode set and readOptions Configure basic Wireless LAN featuresMeans auto select channel. Default value YML902 Example Configure wireless LAN security Valid value string of 79 characters Valid value string of 8 ~ 63 characters Wlan macfilter --mode disabledallowdeny --add MACaddress Configure wireless LAN MAC filterRmac2 MACaddress Configure Wireless Bridge Wireless Distribution System/WDSDescription configure the wireless bridge Synopsis Description set remote bridge MAC addressAdvance Show wireless LAN interface configurationsOptions --config BasicWlan security wpaGTKRekey = Email support@netcomm.com.au Contact Information