NetComm 3G9W manual CLI commands via Telnet, Show all CLI commands

Page 71

3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE

CLI commands via Telnet

Show all CLI commands

Description: List all available CLI commands that the 3G router supports.

Synopsis: help ?

Example:

>help

?

help logout reboot atm ddns dumpcfg ping sntp sysinfo tftp wlan sierra qos version build

YML902 – 71

Image 71
Contents 3G9W Hspa 7.2 Mbps Wi-Fi Router Preface Important Notice and Safety PrecautionTable of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents FeaturesPowered off LED IndicatorsColor Mode Description Green Power on Off Power off LAN 1~4Rear Panel Rear panel contains the ports for data and power connectionsQuick Setup Save the router configuration and reboot see section Quick SetupSetup Procedure Configure the router through the Web User Interface WUIWeb User Interface Web User Interface Default SettingsClick OK to submit the settings TCP/IP SettingsDhcp Mode To login to the web interface, follow the steps below Login ProcedureBasic / Home Web User Interface HomepageFields Description Following table provides further details3G Settings This menu includes 3G service Setup and PIN Configuration 3G Settings3G Service Setup 21 for instruction on how to fix this PIN Lock Off PIN ConfigurationPIN Code Protection YML902 PIN Code Change Wireless Wireless Option Description SetupSecurity Click Save/Apply to configure the wireless security optionsSelect Ssid Card. If the Ssid does not match, access is deniedAuthentication WEP Encryption will also be enabledConfiguration Point can be linked Broadcast and multicast messages. The default isDefault is disabled AP Isolation54g Protection 54g Mode802.11b only mode Mbit/s Dsss specification as described in Ieee StdCan be added Deny Rejects access for the specified MAC addressesMAC Filter MAC AddressFeature Options Wireless BridgeClick Save/Apply to implement new configuration settings Associated Authorized Lists those devices with authorized accessStation Info Is generated randomlyManagement Management Device SettingsRestore Default Update SettingsDefault screen upon successful installation Access Control YML902 Simple Network Time Protocol Sntp Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced SetupNo client subscribes to a multicast group Configuration ProtocolLocal Area Network LAN Igmp SnoopingPort Forwarding Network Address Translation NATExternal Port End Is selected the port ranges are automatically configuredSelected the port ranges are automatically configured Options DescriptionPort Triggering Open Port End Demilitarized DMZ HostTrigger Port End Trigger Protocol TCP, TCP/UDP or UDP Open Port StartSecurity Options Description MAC address of the PC running the browser Parental ControlUser Name User-defined label for this restriction Routing YML902 YML902 Domain Name Servers DNS DNS Server ConfigurationOptions Descriptions Dynamic DNSStatus Status Test Description DiagnosticsSystem Log Click View System Log. The results are displayed as follows 3G Status Status Description Strongest cells Network Registration Status BCS Battery Charge LevelStatus Quality Ec/IoInterface Shows connection interfaces StatisticsService Shows the service type But may be needed by routing daemons RouteSelect Route to display the paths the Router has found Field DescriptionClick Dhcp to display the Dhcp information Dynamic Host Configuration Protocol DhcpARP Click ARP to display the ARP informationCLI commands Via Telnet Show all CLI commands CLI commands via TelnetEnd the telnet session Reset/reboot deviceRadio Signal Strength Connection status Radio BandImsi & Imei read Wireless LAN mode set and readOptions Configure basic Wireless LAN featuresMeans auto select channel. Default value YML902 Example Configure wireless LAN security Valid value string of 79 characters Valid value string of 8 ~ 63 characters Wlan macfilter --mode disabledallowdeny --add MACaddress Configure wireless LAN MAC filterRmac2 MACaddress Configure Wireless Bridge Wireless Distribution System/WDSDescription configure the wireless bridge Synopsis Description set remote bridge MAC addressAdvance Show wireless LAN interface configurationsOptions --config BasicWlan security wpaGTKRekey = Email support@netcomm.com.au Contact Information