NetComm 3G9W manual Radio Band, Connection status

Page 73

3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE

Radio Band

Description: Display the 3G band

Synopsis: sierra show --band Example:

> sierra show --band band: IMT2000

Note: IMT2000 is band 2100 and WCDMA800 is band 850

Connection status

Description: Display the 3G network connection status

Synopsis: sierra show –link sierra show --gstatus

Examples:

>sierra show --link link: Connected

>sierra show --gstatus

Current Time:

450

Temperature: 45

Bootup Time:

1

Mode:

ONLINE

System mode:

WCDMA

PS state:

Attached

WCDMA band:

WCDMA800

GSM band:

Unknown

WCDMA channel: 4436

GSM channel: 65535

GMM (PS) state:REGISTERED

NORMAL SERVICE

MM (CS) state: IDLE

NORMAL SERVICE

WCDMA L1 State:L1M_FACH

RRC State: CELL_FACH

RX level (dBm):-90

 

YML902 – 73

Image 73
Contents 3G9W Hspa 7.2 Mbps Wi-Fi Router Preface Important Notice and Safety PrecautionTable of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents FeaturesColor Mode Description LED IndicatorsGreen Power on Off Power off LAN 1~4 Powered offRear Panel Rear panel contains the ports for data and power connectionsQuick Setup Setup Procedure Quick SetupConfigure the router through the Web User Interface WUI Save the router configuration and reboot see sectionWeb User Interface Web User Interface Default SettingsDhcp Mode TCP/IP SettingsClick OK to submit the settings To login to the web interface, follow the steps below Login ProcedureBasic / Home Web User Interface HomepageFields Description Following table provides further details3G Settings 3G Service Setup 3G SettingsThis menu includes 3G service Setup and PIN Configuration 21 for instruction on how to fix this PIN Code Protection PIN ConfigurationPIN Lock Off YML902 PIN Code Change Wireless Wireless Option Description SetupSecurity Click Save/Apply to configure the wireless security optionsAuthentication Card. If the Ssid does not match, access is deniedWEP Encryption will also be enabled Select SsidConfiguration Default is disabled Broadcast and multicast messages. The default isAP Isolation Point can be linked802.11b only mode 54g ModeMbit/s Dsss specification as described in Ieee Std 54g ProtectionMAC Filter Deny Rejects access for the specified MAC addressesMAC Address Can be addedClick Save/Apply to implement new configuration settings Wireless BridgeFeature Options Station Info Authorized Lists those devices with authorized accessIs generated randomly AssociatedManagement Management Device SettingsRestore Default Update SettingsDefault screen upon successful installation Access Control YML902 Simple Network Time Protocol Sntp Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced SetupLocal Area Network LAN Configuration ProtocolIgmp Snooping No client subscribes to a multicast groupPort Forwarding Network Address Translation NATSelected the port ranges are automatically configured Is selected the port ranges are automatically configuredOptions Description External Port EndPort Triggering Trigger Port End Demilitarized DMZ HostTrigger Protocol TCP, TCP/UDP or UDP Open Port Start Open Port EndSecurity Options Description User Name User-defined label for this restriction Parental ControlMAC address of the PC running the browser Routing YML902 YML902 Domain Name Servers DNS DNS Server ConfigurationOptions Descriptions Dynamic DNSStatus Status Test Description DiagnosticsSystem Log Click View System Log. The results are displayed as follows 3G Status Status Description Status Status BCS Battery Charge LevelQuality Ec/Io Strongest cells Network RegistrationInterface Shows connection interfaces StatisticsService Shows the service type Select Route to display the paths the Router has found RouteField Description But may be needed by routing daemonsARP Dynamic Host Configuration Protocol DhcpClick ARP to display the ARP information Click Dhcp to display the Dhcp informationCLI commands Via Telnet Show all CLI commands CLI commands via TelnetRadio Signal Strength Reset/reboot deviceEnd the telnet session Connection status Radio BandImsi & Imei read Wireless LAN mode set and readOptions Configure basic Wireless LAN featuresMeans auto select channel. Default value YML902 Example Configure wireless LAN security Valid value string of 79 characters Valid value string of 8 ~ 63 characters Wlan macfilter --mode disabledallowdeny --add MACaddress Configure wireless LAN MAC filterDescription configure the wireless bridge Synopsis Configure Wireless Bridge Wireless Distribution System/WDSDescription set remote bridge MAC address Rmac2 MACaddressOptions --config Show wireless LAN interface configurationsBasic AdvanceWlan security wpaGTKRekey = Email support@netcomm.com.au Contact Information