NetComm 3G9W manual Routing

Page 53

3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE

7.4Routing

Default Gateway, Static Route and Dynamic Route settings can be found in the Routing link as illustrated below.

7.4.1Default Gateway

If the Enable Automatic Assigned Default Gateway checkbox is selected, this device will accept a default Gateway assignment. If the checkbox is not selected, a field will appear allowing you to enter the static default gateway and/or WAN interface, then click Save/Apply.

NOTE:

After enabling the Automatic Assigned Default Gateway, you must re-boot the Router to activate the assigned default Gateway.

YML902 – 53

Image 53

Contents 3G9W Hspa 7.2 Mbps Wi-Fi Router Preface Important Notice and Safety PrecautionTable of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents FeaturesColor Mode Description LED IndicatorsGreen Power on Off Power off LAN 1~4 Powered offRear Panel Rear panel contains the ports for data and power connectionsQuick Setup Setup Procedure Quick SetupConfigure the router through the Web User Interface WUI Save the router configuration and reboot see sectionWeb User Interface Web User Interface Default SettingsClick OK to submit the settings TCP/IP SettingsDhcp Mode To login to the web interface, follow the steps below Login ProcedureBasic / Home Web User Interface HomepageFields Description Following table provides further details3G Settings This menu includes 3G service Setup and PIN Configuration 3G Settings3G Service Setup 21 for instruction on how to fix this PIN Lock Off PIN ConfigurationPIN Code Protection YML902 PIN Code Change Wireless Wireless Option Description SetupSecurity Click Save/Apply to configure the wireless security optionsAuthentication Card. If the Ssid does not match, access is deniedWEP Encryption will also be enabled Select SsidConfiguration Default is disabled Broadcast and multicast messages. The default isAP Isolation Point can be linked802.11b only mode 54g ModeMbit/s Dsss specification as described in Ieee Std 54g ProtectionMAC Filter Deny Rejects access for the specified MAC addressesMAC Address Can be addedFeature Options Wireless BridgeClick Save/Apply to implement new configuration settings Station Info Authorized Lists those devices with authorized accessIs generated randomly AssociatedManagement Management Device SettingsRestore Default Update SettingsDefault screen upon successful installation Access Control YML902 Simple Network Time Protocol Sntp Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced SetupLocal Area Network LAN Configuration ProtocolIgmp Snooping No client subscribes to a multicast groupPort Forwarding Network Address Translation NATSelected the port ranges are automatically configured Is selected the port ranges are automatically configuredOptions Description External Port EndPort Triggering Trigger Port End Demilitarized DMZ HostTrigger Protocol TCP, TCP/UDP or UDP Open Port Start Open Port EndSecurity Options Description MAC address of the PC running the browser Parental ControlUser Name User-defined label for this restriction Routing YML902 YML902 Domain Name Servers DNS DNS Server ConfigurationOptions Descriptions Dynamic DNSStatus Status Test Description DiagnosticsSystem Log Click View System Log. The results are displayed as follows 3G Status Status Description Status Status BCS Battery Charge LevelQuality Ec/Io Strongest cells Network RegistrationInterface Shows connection interfaces StatisticsService Shows the service type Select Route to display the paths the Router has found RouteField Description But may be needed by routing daemonsARP Dynamic Host Configuration Protocol DhcpClick ARP to display the ARP information Click Dhcp to display the Dhcp informationCLI commands Via Telnet Show all CLI commands CLI commands via TelnetEnd the telnet session Reset/reboot deviceRadio Signal Strength Connection status Radio BandImsi & Imei read Wireless LAN mode set and readOptions Configure basic Wireless LAN featuresMeans auto select channel. Default value YML902 Example Configure wireless LAN security Valid value string of 79 characters Valid value string of 8 ~ 63 characters Wlan macfilter --mode disabledallowdeny --add MACaddress Configure wireless LAN MAC filterDescription configure the wireless bridge Synopsis Configure Wireless Bridge Wireless Distribution System/WDSDescription set remote bridge MAC address Rmac2 MACaddressOptions --config Show wireless LAN interface configurationsBasic AdvanceWlan security wpaGTKRekey = Email support@netcomm.com.au Contact Information