NetComm 3G9W Local Area Network LAN, Igmp Snooping, No client subscribes to a multicast group

Page 45

3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE

7.1Local Area Network (LAN)

This screen allows you to configure the Local Area Network (LAN) interface on your Router.

See the field descriptions below for more details.

Option

Description

 

 

IP Address

Enter the IP address for the LAN interface

 

 

Subnet Mask

Enter the subnet mask for the LAN interface

 

 

Enable UPnP

Tick the box to enable Universal Plug and Play

 

 

Enable Internet Group

Enable by ticking the box

Management Protocol

Standard Mode: In standard mode, multicast traffic will flood to all bridge ports when

(IGMP) Snooping

no client subscribes to a multicast group.

 

 

Blocking Mode: In blocking mode, the multicast data traffic will be blocked. When

 

there are no client subscriptions to a multicast group, it will not flood to the bridge ports.

 

 

Dynamic Host

Select Enable DHCP server and enter your starting and ending IP addresses and

Configuration Protocol

the lease time. This setting configures the router to automatically assign IP, default

(DHCP) Server

gateway and DNS server addresses to every DHCP client on your LAN

 

 

Configure a second IP address by ticking the checkbox shown below and enter the following information:

IP Address:

Enter the secondary IP address for the LAN interface.

 

 

Subnet Mask:

Enter the secondary subnet mask for the LAN interface.

NOTE:

The Save button saves new settings to allow continued configuration, while the Save/Reboot button not only saves new settings

 

but also reboots the device to apply the new configuration (i.e. all new settings).

YML902 – 45

Image 45
Contents 3G9W Hspa 7.2 Mbps Wi-Fi Router Preface Important Notice and Safety PrecautionTable of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents FeaturesColor Mode Description LED IndicatorsGreen Power on Off Power off LAN 1~4 Powered offRear Panel Rear panel contains the ports for data and power connectionsQuick Setup Setup Procedure Quick SetupConfigure the router through the Web User Interface WUI Save the router configuration and reboot see sectionWeb User Interface Web User Interface Default SettingsTCP/IP Settings Dhcp ModeClick OK to submit the settings To login to the web interface, follow the steps below Login ProcedureBasic / Home Web User Interface HomepageFields Description Following table provides further details3G Settings 3G Settings 3G Service SetupThis menu includes 3G service Setup and PIN Configuration 21 for instruction on how to fix this PIN Configuration PIN Code ProtectionPIN Lock Off YML902 PIN Code Change Wireless Wireless Option Description SetupSecurity Click Save/Apply to configure the wireless security optionsAuthentication Card. If the Ssid does not match, access is deniedWEP Encryption will also be enabled Select SsidConfiguration Default is disabled Broadcast and multicast messages. The default isAP Isolation Point can be linked802.11b only mode 54g ModeMbit/s Dsss specification as described in Ieee Std 54g ProtectionMAC Filter Deny Rejects access for the specified MAC addressesMAC Address Can be addedWireless Bridge Click Save/Apply to implement new configuration settingsFeature Options Station Info Authorized Lists those devices with authorized accessIs generated randomly AssociatedManagement Management Device SettingsRestore Default Update SettingsDefault screen upon successful installation Access Control YML902 Simple Network Time Protocol Sntp Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced SetupLocal Area Network LAN Configuration ProtocolIgmp Snooping No client subscribes to a multicast groupPort Forwarding Network Address Translation NATSelected the port ranges are automatically configured Is selected the port ranges are automatically configuredOptions Description External Port EndPort Triggering Trigger Port End Demilitarized DMZ HostTrigger Protocol TCP, TCP/UDP or UDP Open Port Start Open Port EndSecurity Options Description Parental Control User Name User-defined label for this restrictionMAC address of the PC running the browser Routing YML902 YML902 Domain Name Servers DNS DNS Server ConfigurationOptions Descriptions Dynamic DNSStatus Status Test Description DiagnosticsSystem Log Click View System Log. The results are displayed as follows 3G Status Status Description Status Status BCS Battery Charge LevelQuality Ec/Io Strongest cells Network RegistrationInterface Shows connection interfaces StatisticsService Shows the service type Select Route to display the paths the Router has found RouteField Description But may be needed by routing daemonsARP Dynamic Host Configuration Protocol DhcpClick ARP to display the ARP information Click Dhcp to display the Dhcp informationCLI commands Via Telnet Show all CLI commands CLI commands via TelnetReset/reboot device Radio Signal StrengthEnd the telnet session Connection status Radio BandImsi & Imei read Wireless LAN mode set and readOptions Configure basic Wireless LAN featuresMeans auto select channel. Default value YML902 Example Configure wireless LAN security Valid value string of 79 characters Valid value string of 8 ~ 63 characters Wlan macfilter --mode disabledallowdeny --add MACaddress Configure wireless LAN MAC filterDescription configure the wireless bridge Synopsis Configure Wireless Bridge Wireless Distribution System/WDSDescription set remote bridge MAC address Rmac2 MACaddressOptions --config Show wireless LAN interface configurationsBasic AdvanceWlan security wpaGTKRekey = Email support@netcomm.com.au Contact Information