Multi-Tech Systems Hub manual FCC Part 15 Regulation, Canadian Limitations Notice, Industry Canada

Page 36

Appendices

Canadian Limitations Notice

Notice: The ringer equivalence number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination of a interface may consist of any combination of devices subject only to the requirement that the sum of the ringer equivalence numbers of all the devices does not exceed 5.

Notice: The Industry Canada label identifies certificated equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Industry Canada does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

FCC Part 15 Regulation

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference.

(2)This device must accept any interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.

36

CommPlete 4000 Communications Server User Guide

Image 36
Contents User Guide Record of Revisions PatentsContents Appendices System Overview Product OverviewDocumentation Set Overview RASExpressTechnical Specifications Power SupplyDimensions ChassisSafety Warnings UnpackingRack Mounting Cable ConnectionsSBC Board Cabling SBC BoardISI Board Cabling Shared Interrupt For Top Slots Identical Devices RequiredSerial Card Upgrades Powering Up Power Supply ConnectorsAccessing RASExpress What you need to startA8. Type the IP Subnet Mask CommPlete 4000 Communications Server User Guide B8. Type the IP Subnet Mask Using Dial-In Access Hardware removal/Replacement Disconnecting Cables and Removal from EnclosureCard Cage Removal/Replacement Cover Mounting ScrewsRed Red Orange RedRed White Board Removal and Replacement Removing SBC BoardHard Disk Drive Removal/Replacement Removing ISI BoardsFloppy Disk Drive Removal/Replacement Cdrom Removal/ReplacementPower Supply Removal/Replacement Troubleshooting SBC does not boot correctly or hangs after video appearsNo Video COM1, COM2, or LPT1 port does not respond correctlyDiagnostic Tests Invalid Time, Date or SetupKeyboard does not respond to key strokes Limited Warranty Addendum for North American ProductsOut of Warranty Repair Costs On-line Warranty Registration Technical SupportAddendum for International Products Recording CommPlete 4000 InformationOrdering Accessories ServiceContacting Technical Support Appendix A-Back Panel Connector Pinouts VGA 15-Pin ConnectorPinDescription Pin DB9 COM 1 Connector Pin Circular JackPin Description RJ-45 Connector Pin Floppy Disk Drive ConnectorPrinter Port Connector COM 2 Port ConnectorPinSignal Name Direction Hard Disk Connector IOCS16Appendices FCC Part 15 Regulation Canadian Limitations NoticeIndustry Canada Compliance with Babt Requirements Example Diagram Showing Creepage Clearance Distances European Low Voltage DirectiveCompliance with BS6789 .1 and Part Compliance with BS6328 PartEMC, Safety, and Terminal Directive Compliance