Multi-Tech Systems MT5634ZBA-V-V92 Appendix C Regulatory Compliance, FCC Part 15 Regulation

Page 32

Appendix C – Regulatory Compliance

Appendix C – Regulatory

Compliance

FCC Part 15 Regulation

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation.

WARNING – Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Part 68 Telecom

1.This equipment complies with Part 68 of the Federal Communications Commission Rules. On the outside surface of this equipment is a label that contains, among other information, the FCC registration number. This information must be provided to the telephone company.

2.The suitable USOC jack (Universal Service Order Code connecting arrangement) for this equipment is shown below. If applicable, the facility interface codes (FIC) and service order codes (SOC) are shown.

3.An FCC-compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack that is Part 68 compliant.

4.The ringer equivalence number (REN) is used to determine the number of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in the device not ringing in response to an incoming call. In most, but not all, areas the sum of the RENs should not exceed 5.0. To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the local telephone company.

5.If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

6.The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications in order to maintain uninterrupted service.

7.If trouble is experienced with this equipment (the model of which is indicated below) please contact Multi-Tech Systems, Inc. at the address shown below for details of how to have repairs made. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.

8.No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its licensees. Unauthorized repairs void registration and warranty.

9.This equipment should not be used on party lines or coin lines.

10.If so required, this equipment is hearing aid compatible.

11. Manufacturer:

Multi-Tech Systems, Inc.

 

 

Trade Name:

MultiModem ZBA

 

 

Model Number:

MT5634ZBA

 

 

FCC Registration No:

AU7USA-24713-M5-E

 

 

Ringer Equivalence:

0.3B

 

 

Modular Jack (USOC):

RJ11C or RJ11W (single line)

 

 

Service Center in USA:

Multi-Tech Systems, Inc.

 

 

 

2205 Woodale Drive

 

 

 

Mounds View, MN 55112 U.S.A.

 

 

 

(763) 785-3500 Fax (763) 785-9874

 

 

 

 

 

Multi-Tech Systems, Inc. MT5634ZBA-Series User Guide (S000286G)

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents MultiModem ZBA MultiModem ZBA MT5634ZBA-Series User Guide Table of Contents Table of Contents Features Table IntroductionFeatures Specific to Installation Safety WarningsChange the Internal Jumpers Opening the ModemChanging the Voice Jumper Non-Global Connection Connect the Modem to Your PCGlobal Connections Connect the Two-Wire Leased Line Leased Line Only Connect the Modem to the AC Power OutletPower-On Test Connect the Modem to Your PCInstall the Modem Driver Installing the Modem DriverUsing the Global Wizard to Configure Your Modem Using AT Commands to Configure Your ModemConfigure the modem for best performance Modem Serial Speed GuidelinesOperation About the Front PanelOperation SetupLeased-Line Operation Connecting to the Internet AT Commands, S- Registers, and Result Codes Remote Configuration Basic ProcedureSetup Changing the Setup PasswordTurning Callback Security On and Off Changing the Setup PasswordCallback Security Setting Callback Security Message Parity Assigning Callback Passwords and Phone NumbersCalling Procedures Password-Only CallbackNumber-Entry Callback Extension-Entry CallbackCallback Security Commands Direct ConnectionCallback Assignments Form Modem Does Not Respond to Commands TroubleshootingNone of the Indicators Light Lack of a physical connection to the telephone line Page Data Is Being Lost There Are Garbage Characters on the MonitorModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeAppendix a Technical Specifications Fax Data RatesReceiver Sensitivity Upgrade Overview Appendix B Upgrading the Modem’s FirmwareIdentify the Modem Firmware Identify the Current Firmware VersionDownload the Upgrade File Extract the Upgrade FilesUpgrade the Modem’s Firmware Restore Your ParametersFCC Part 68 Telecom Appendix C Regulatory ComplianceFCC Part 15 Regulation EMC, Safety and R&TTE Directive Compliance Canadian Limitations NoticeIndustry Canada International Modem RestrictionsNew Zealand Telecom Warning Notice South African StatementAppendix D Waste Electrical and Electronic Equipment Weee Waste Electrical and Electronic Equipment StatementAppendix E Installing a Modem under Linux SetupAppendix F Connecting to a Cisco Router Connecting to a Cisco Router Console PortRemote Configuration Console Port ConnectionsAppendix G Warranty, Service, and Technical Support Multi-Tech Warranty StatementRepair Procedures for International Distributors Appendix H Rohs HT/TS Substance Concentration AT commands IndexSpeed
Top Page Image Contents