Multi-Tech Systems MT5634ZBA-V-V92 manual Canadian Limitations Notice, Industry Canada

Page 33

Appendix C – Regulatory Compliance

Canadian Limitations Notice

Notice: The ringer equivalence number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the ringer equivalence numbers of all the devices does not exceed 5.

Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Industry Canada label does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

Industry Canada

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Reglement Canadien sur le matériel brouilleur.

EMC, Safety and R&TTE Directive Compliance

The CE mark is affixed to this product to confirm compliance with the following European Community Directives:

Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of Member States relating to electromagnetic compatibility.

and

Council Directive 73/23/EEC of 19 February 1973 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits:

and

Council Directive 1999/5/EC of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity.

International Modem Restrictions

Some dialing and answering defaults and restrictions may vary for international modems. Changing settings may cause a modem to become non-compliant with national telecom requirements in specific countries. Also note that some software packages may have features or lack restrictions that may cause the modem to become non-compliant.

Multi-Tech Systems, Inc. MT5634ZBA-Series User Guide (S000286G)

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents MultiModem ZBA MultiModem ZBA MT5634ZBA-Series User Guide Table of Contents Table of Contents Introduction Features TableFeatures Specific to Safety Warnings InstallationChange the Internal Jumpers Opening the ModemChanging the Voice Jumper Connect the Modem to Your PC Global ConnectionsNon-Global Connection Connect the Modem to the AC Power Outlet Connect the Two-Wire Leased Line Leased Line OnlyPower-On Test Connect the Modem to Your PCInstalling the Modem Driver Install the Modem DriverUsing AT Commands to Configure Your Modem Using the Global Wizard to Configure Your ModemModem Serial Speed Guidelines Configure the modem for best performanceAbout the Front Panel OperationSetup Leased-Line OperationOperation Connecting to the Internet AT Commands, S- Registers, and Result Codes Basic Procedure Remote ConfigurationSetup Changing the Setup PasswordChanging the Setup Password Callback SecurityTurning Callback Security On and Off Assigning Callback Passwords and Phone Numbers Setting Callback Security Message ParityCalling Procedures Password-Only CallbackExtension-Entry Callback Number-Entry CallbackDirect Connection Callback Security CommandsCallback Assignments Form Troubleshooting None of the Indicators LightModem Does Not Respond to Commands Lack of a physical connection to the telephone line Page There Are Garbage Characters on the Monitor Data Is Being LostModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeFax Data Rates Appendix a Technical SpecificationsReceiver Sensitivity Appendix B Upgrading the Modem’s Firmware Upgrade OverviewIdentify the Modem Firmware Identify the Current Firmware VersionExtract the Upgrade Files Download the Upgrade FileUpgrade the Modem’s Firmware Restore Your ParametersAppendix C Regulatory Compliance FCC Part 15 RegulationFCC Part 68 Telecom Canadian Limitations Notice EMC, Safety and R&TTE Directive ComplianceIndustry Canada International Modem RestrictionsSouth African Statement New Zealand Telecom Warning NoticeWeee Waste Electrical and Electronic Equipment Statement Appendix D Waste Electrical and Electronic EquipmentSetup Appendix E Installing a Modem under LinuxConnecting to a Cisco Router Console Port Appendix F Connecting to a Cisco RouterConsole Port Connections Remote ConfigurationMulti-Tech Warranty Statement Appendix G Warranty, Service, and Technical SupportRepair Procedures for International Distributors Appendix H Rohs HT/TS Substance Concentration Index AT commandsSpeed
Top Page Image Contents