Multi-Tech Systems MT9234ZBA-V manual FCC Part 15 Regulation, FCC Part 68 Telecom

Page 29

Appendix B – Regulatory Compliance

Appendix B – Regulatory Compliance

FCC Part 15 Regulation

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation.

WARNING – Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Part 68 Telecom

1.This equipment complies with Part 68 of the Federal Communications Commission Rules. On the outside surface of this equipment is a label that contains, among other information, the FCC registration number. This information must be provided to the telephone company.

2.The suitable USOC jack (Universal Service Order Code connecting arrangement) for this equipment is shown below. If applicable, the facility interface codes (FIC) and service order codes (SOC) are shown.

3.An FCC-compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack that is Part 68 compliant.

4.The ringer equivalence number (REN) is used to determine the number of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in the device not ringing in response to an incoming call. In most, but not all, areas the sum of the RENs should not exceed 5.0. To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the local telephone company.

5.If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

6.The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications in order to maintain uninterrupted service.

7.If trouble is experienced with this equipment (the model of which is indicated below) please contact Multi-Tech Systems, Inc. at the address shown below for details of how to have repairs made. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.

8.No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its licensees. Unauthorized repairs void registration and warranty.

9.This equipment should not be used on party lines or coin lines.

10.If so required, this equipment is hearing aid compatible.

11. Manufacturer:

Multi-Tech Systems, Inc.

Trade Name:

MultiModem® ZBA

Model Number:

MT9234ZBA

FCC Registration No:

AU7USA-24713-M5-E

Ringer Equivalence:

0.3B

Modular Jack (USOC):

RJ11

Service Center in USA:

Multi-Tech Systems, Inc.

 

2205 Woodale Drive

 

Mounds View, MN 55112 U.S.A.

 

(763) 785-3500 Fax (763) 785-9874

 

 

 

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents MultiModem ZBA Revisions Table of Contents Table of Contents Introduction FeaturesTechnical Specifications Diagnostics Safety Warnings InstallationChange the Internal Jumpers Opening the ModemChanging the Voice Jumper Connect the Modem to Your PC Install the Modem Driver Using AT Commands to Configure Your Modem Operation SetupAbout the Front Panel Leased-Line OperationConnecting to the Internet Basic Procedure Remote ConfigurationSetup Changing the Setup PasswordTurning Callback Security On and Off Changing the Setup PasswordCallback Security Assigning Callback Passwords and Phone Numbers Setting Callback Security Message ParityCalling Procedures Password-Only CallbackExtension-Entry Callback Number-Entry CallbackDirect Connection Callback Security CommandsCallback Assignments Form Modem Does Not Respond to Commands TroubleshootingNone of the Indicators Light Modem Cannot Connect When Dialing Page There Are Garbage Characters on the Monitor Data Is Being LostModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeRepair Procedures for U.S. and Canadian Customers Warranty, Service, and Technical SupportMulti-Tech Warranty Statement Replacement Parts Repair Procedures for International DistributorsDownload the Upgrade File Upgrade OverviewAppendix a Upgrading the Modem’s Firmware Identify the Modem FirmwareUpgrade the Modem’s Firmware Extract the Upgrade FilesRestore Your Parameters Clear Your Stored ParametersFCC Part 68 Telecom FCC Part 15 RegulationFax Branding Statement EMC, Safety and R&TTE Directive ComplianceCanadian Limitations Notice Industry CanadaSouth African Statement International Modem RestrictionsNew Zealand Telecom Warning Notice Weee Waste Electrical and Electronic Equipment Statement Appendix C Waste Electrical and Electronic EquipmentSetup Appendix D Installing a Modem under LinuxConnecting to a Cisco Router Console Port Appendix E Connecting to a Cisco RouterConsole Port Connections Remote Configuration依照中国标准的有毒有害物质信息 Appendix F C-ROHS HT/TS Substance ConcentrationIndex AT commandsTelephone
Related manuals
Manual 35 pages 52.39 Kb Manual 35 pages 61.01 Kb

MT9234ZBA-V, MT9234ZBA specifications

Multi-Tech Systems has long been a trusted name in the field of communication technology, and its MT9234ZBA and MT9234ZBA-V modem products exemplify the company's commitment to delivering robust and reliable connectivity solutions. These modems are ideal for a range of applications, including telephony, data communication, and remote monitoring, making them a versatile choice for both personal and professional use.

One of the standout features of the MT9234ZBA and MT9234ZBA-V is their high-speed data transmission capabilities. Both models support data rates of up to 56 Kbps, ensuring efficient and swift data transfer for various applications. This allows users to experience minimal latency during downloads and uploads, appealing to those who depend on timely and reliable data delivery.

These modems utilize advanced technologies, such as V.92 and V.90 protocols, which enable users to benefit from features like quick connect, thereby reducing the time it takes to establish a connection. Additionally, the modems support both analog and digital lines, making them adaptable for different environments and infrastructures.

Another notable characteristic of the MT9234ZBA and MT9234ZBA-V modems is their compatibility with a wide range of operating systems, including various versions of Windows, Linux, and Mac OS. This cross-platform support ensures that users can easily integrate these modems into their existing software environments without encountering significant compatibility issues.

The design and construction of these modems are also worth mentioning. They are compact and lightweight, making them easy to install and reposition as needed. Their robust construction ensures longevity, which is crucial for users in environments where durability is paramount.

For those concerned about security, Multi-Tech Systems has integrated multiple security features within these modems. This includes support for encryption protocols, ensuring that data transmitted over the modem remains secure and protected from unauthorized access.

In conclusion, the MT9234ZBA and MT9234ZBA-V by Multi-Tech Systems represent an excellent choice for anyone in need of reliable and high-speed modem solutions. With their advanced features, compatibility with various operating systems, and emphasis on security, these modems stand out in the crowded telecommunications market. Whether for home use or in a professional setting, the MT9234ZBA and MT9234ZBA-V offer robust solutions for modern communication needs.
Top Page Image Contents