Multi-Tech Systems MT9234ZBA-V manual Index, AT commands

Page 37

Index

Index

A
AT commands
&D	13
&F	13
&W	13, 16
O	16
AT Commands	5
Autoanswer	24
Autobaud	13
B
Baud Rate	13
C
Call Waiting	24
Callback Security	17
Caller ID	13, 24
Canadian Limitations Notice	31
Change the Internal Jumpers	8
Changing the Dial-Up/Leased-Line Jumper	9
Changing the Voice Jumper	9
Configuration, Storing a	13
Configure the Modem for Your Country/Region	12
Configure the Modem Using AT Commands	12
Configure the Modem Using the Global Wizard	12
Connect Messages	13
Connecting the Modem to the PC	10
Connecting to a Cisco Router	35
Connecting to the Internet	15
D
Data Communications Software	13
Data Terminal Ready command	13
Default Settings	13
Dial-up Operation	9
Driver Installation	12
DTE Rate	13
DTR (Data Terminal Ready) Control command	13, 24
E
European Community Directives	31
F
Fax Branding Statement	31
FCC Regulations	30
Features Table	7
Firmware
Upgrading	28
Flash Memory	28
Flash Wizard Upgrade Utility	28
Front Panel	14, 22

G
Garbage Characters	25
Global Wizard	12
I
Indicators	14, 22
Initialization Strings	13
Installation and Setup	8
Installing the Modem Driver	12
Internal Jumpers	11
International Modem Restrictions	32
Internet Addresses	27
J
Jumpers	11
L
Leased Line Operation	9
Leased-Line Operation	15
LED Indicators	14, 22
Line Connection	11
Linux	34
Load Factory Settings command	13
Lost Data	25
M
MNP 5 Data Compression	24
Modem Driver Installation	12
Multi-Tech Internet Sites	27
N
New Zealand Telecom Warning Notice	32
O
Ordering Replacement Parts	27
P
PhoneTools	13
PhoneTools Program	14
Protocols	24
R
Remote Configuration	16
Escape Character	16
Replacement Parts	27
Result Codes	5
Rings, Setting Number of	13
RS-232 Connection	11


Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)	37

Image 37

Contents MultiModem ZBA Revisions Table of Contents Table of Contents Introduction FeaturesTechnical Specifications Diagnostics Safety Warnings InstallationChange the Internal Jumpers Opening the ModemChanging the Voice Jumper Connect the Modem to Your PC Install the Modem Driver Using AT Commands to Configure Your Modem Operation SetupAbout the Front Panel Leased-Line OperationConnecting to the Internet Basic Procedure Remote ConfigurationSetup Changing the Setup PasswordCallback Security Changing the Setup PasswordTurning Callback Security On and Off Assigning Callback Passwords and Phone Numbers Setting Callback Security Message ParityCalling Procedures Password-Only CallbackExtension-Entry Callback Number-Entry CallbackDirect Connection Callback Security CommandsCallback Assignments Form None of the Indicators Light TroubleshootingModem Does Not Respond to Commands Modem Cannot Connect When Dialing Page There Are Garbage Characters on the Monitor Data Is Being LostModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeMulti-Tech Warranty Statement Warranty, Service, and Technical SupportRepair Procedures for U.S. and Canadian Customers Replacement Parts Repair Procedures for International DistributorsDownload the Upgrade File Upgrade OverviewAppendix a Upgrading the Modem’s Firmware Identify the Modem FirmwareUpgrade the Modem’s Firmware Extract the Upgrade FilesRestore Your Parameters Clear Your Stored ParametersFCC Part 68 Telecom FCC Part 15 RegulationFax Branding Statement EMC, Safety and R&TTE Directive ComplianceCanadian Limitations Notice Industry CanadaNew Zealand Telecom Warning Notice International Modem RestrictionsSouth African Statement Weee Waste Electrical and Electronic Equipment Statement Appendix C Waste Electrical and Electronic EquipmentSetup Appendix D Installing a Modem under Linux Connecting to a Cisco Router Console Port Appendix E Connecting to a Cisco RouterConsole Port Connections Remote Configuration依照中国标准的有毒有害物质信息 Appendix F C-ROHS HT/TS Substance ConcentrationIndex AT commandsTelephone

Related manuals

Manual 35 pages 52.39 Kb

Manual 35 pages 61.01 Kb