Multi-Tech Systems FR3100, FR3060 manual Glossary

Page 97

Glossary

H

Handshaking: A process that two modems go through at the time of call setup to establish synchronization over the data communica- tions link. It is a synchronization and negotiation process accomplished by the exchange of predefined, mutually recognized control codes.

High-level Data Link Control (HDLC): An ISO standard, bit-oriented data communications protocol that provides nearly error-free data transfers.

I

Hexadecimal: A base 16 numbering system used to represent binary values. Hex uses the numbers 0-9 and the letters A-F: usually notated by an "h" (e.g., "4CF h", read "four charley fox, hex"). The result is that one hex digit represents a 4-bit value.

Implicit congestion management: A method of informing the terminal that the network is busy. This method relies on the end-system protocol to detect and fix the congestion problem. (TCP/IP is an example of a protocol using only implicit congestion management.) See also "explicit congestion management".

In-band:Refers to the type of signalling over the conversion path on an ISDN call. Contrast "out-of-band".

Insufficient Ones: A T1 error condition that is logged when less than one 1 in 16 0s or less than 12.5 % average 1s density is received.

Inter Exchange Carrier (IEC): The long distance company (LE) who's central office provides the point of reference for T1 access. Any common carrier authorized by the FCC to carry customer transmissions between LATAs.

Internet: Refers to the computer network of many millions of university, government and private users around the world. Each user has a unique Internet Address.

Internet Address (IP Address): A unique 32-bit address for a specific TCP/IP host on a network. Normally printed in dotted decimal format (e.g., 129.128.44.227).

Internet Protocol (IP): A protocol used to route data from its source to its destination in an Internet environment. The Internet Protocol was designed to connect to local area networks. Although there are many protocols that do this, IP refers to the global system of interconnecting computers. It is a highly distributed protocol (each machine only worries about sending data to the next step in the route).

Internetwork Packet Exchange (IPX): A NetWare communications protocol used to route messages from one node to another. IPX packets include network addresses and can be routed from one network to another. An IPX packet can occasionally get lost when crossing networks, thus IPX does not guarantee delivery of a complete message. Either the application has to provide that control, or NetWare's SPX protocol must be used.

Interoperable: Devices from different vendors that can exchange information using a standard's base protocol.

I/O Addresses: Locations within the I/O address space of your computer used by a device, such as an expansion card, a serial port, or an internal modem. The address is used for communication between software and a device.

IRQ Level (Interrupt Request Level): The notification a processor receives when another portion of the computer's hardware requires its attention. IRQs are numbered so that the device issuing the IRQ can be identified, and so IRQs can be prioritized.

ISA (Industry Standards Architecture) (pronounced "ice a"): The classic 8 or 16-bit architecture introduced with IBM's PC-AT computer.

ISDN (Integrated Services Digital Network): An International telecommunications standard for transmitting voice, video and data over a digital communications line. ISDN is a world-wide telecommunications service that uses digital transmission and switching technology to support voice and digital data communications. Frame relay was partially based on ISDN's data link layer protocol (LAPD). Frame relay can be used to transmit across ISDN services offering circuit-switched connection at 64K bps and higher speeds. Contrast Public Switched Telephone Network (PSTN).

ITU-TSS (formerly CCITT): International Telecommunications Union-Telecommunications Sector; the United Nations organization that prepares standards ("Recommendations") for resolving communications issues and problems.

K

Key Telephone System (KTS): Phone devices with multiple buttons that let you select incoming or outgoing CO phone lines directly. Similar in operation to a PBX, except a KTS you don't have to dial a "9" for a call outside the building.

Key Service Unit (KSU): A small device containing the switching electronics for a business key telephone system (KTS).

Key Set: A telephone set with several buttons for call holding, line pickup, intercom, autodialing, etc. Also called a touchtone phone (Ericsson) and a KTS (Key Telephone Set).

97

Image 97
Contents User Guide Record of Revisions RevisionDescription User GuideContents Appendices Introduction and Description MultiFRAD 3000-Series IntroductionPreview of this Guide Composite Link Front Panel DescriptionEthernet Channels 3 through Channels 1Voice/Fax Channels 1 Frame Ground GND Connector Power ConnectorInternal Composite Link T1 DSU Connector Monitor XMT/RCV ConnectorVoice/Fax Channels 1 8 Connectors Channels 3 10 ConnectorsCommand Port Technical SpecificationsChannel Connectors Voice/Fax Channel ConnectorsInstallation Unpacking your MultiFRAD Safety WarningsValid Voice/Fax Channel Connections General Cable Connections Cabling your MultiFRADChannel Cable Connections Voice/Fax Cable Connections Default Jumper Block Positioning ProcedureSoftware Loading and Configuration Loading your Software Software Loading and Configuration MultiFRAD 3000-Series User Guide IP Address Ethernet Mask Frame Type MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Detect and Map Your DLCIs MultiFRAD 3000-Series User Guide Build Your Phone Directory Database MultiFRAD 3000-Series User Guide Click Download Setup MultiFRAD 3000-Series User Guide MultiFRAD Software Before You Begin MultiFRAD Configuration Changing IP Parameters MultiFRAD Software MultiFRAD 3000-Series User Guide Changing IPX Parameters MultiFRAD 3000-Series User Guide MultiFRAD Software Changing Bridging Parameters WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD 3000-Series User Guide MultiFRAD Software MultiFRAD 3000-Series User Guide MultiFRAD Software Data Port Configuration Interface Changing Voice/Fax Channel ParametersFXS Interface FXO Interface Voice/FaxInterface Regional Changing the Phone Directory Database Others Setup Enable Logging of Statistics Statistics IP Statistics STP Spanning Tree Port Statistics IPX Port StatisticsWAN Statistics Snmp StatisticsPPP Statistics Data Port Statistics Frame Relay Statistics MultiFRAD 3000-Series User Guide Remote Configuration and Management Modem-Based Remote ConfigurationRemote Configuration and Management LAN-Based Warranty, Service and Tech Support Telnet Remote ManagementMultiFRAD Management Menu MultiFRAD ConfigurationRemote User Database WEB Browser ManagementRemote Configuration and Management MultiFRAD 3000-Series User Guide Warranty, Service and Tech Support On-line Warranty Registration Limited WarrantyRecording MultiFRAD Information Tech SupportContacting Tech Support via E-mail Multi-Tech BBS ServiceTo log on to the Multi-Tech BBS To Download a fileIf you don’t know the file name About the InternetMultiFRAD 3000-Series User Guide Appendices LAN Cables Appendix a Cabling Diagrams Command Port CableVoice/Fax Channel Connectors RS232C/V.24 * Link Cable Trunk CableCommand Port Remote Configuration CableAppendix B Regulatory Information Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary 100 101 102 103 Index Remote Configuration
Related manuals
Manual 105 pages 51.71 Kb