Multi-Tech Systems MT5600BAV.90, MT5600BLV.90, MT5600BAV.92 manual Using the Front Panel

Page 22

￿￿￿￿￿￿￿￿￿￿￿￿

Chapter 3 - Using the Front Panel

This section describes important LCD screens and options. Many, but by no means all, of the options have￿￿￿￿￿￿AT command equivalents.

Status screens display the current status of the modem. Though limb changes are automatic, certain options can be selected by pressing the ◊ button.

STATUS = IDLE. The modem is ready but inactive. This screen appears when the modem is first turned on, and is the starting point for accessing all other screens. Three options are available from this screen by pressing the ◊ button:

MANUAL ORIG.? Places the modem in originate mode for the time specified by register S7. Use this option to connect to a remote modem by manually dialing the number on a phone con- nected to the local modem. When the remote modem answers, press the Enter button to establish a connection with the remote modem. You can also use this option to temporarily place the modem in originate mode for back-to-back testing.

MANUAL ANSWER? Places the modem in answer mode for the time specified by register S7. You can use this option to tempo- rarily place the modem in answer mode for back-to-back testing.

BUSY OUT MODEM? Takes the modem out of service by put- ting it into an off-hook state so that a calling modem receives a busy signal.

MODEM BUSIED OUT. Shows that the modem is busied out. To return the modem to normal service, press ◊, Enter.

STATUS = ONLINE. The modem is connected to another modem. Two options are available from this screen by pressing the ◊ button:

Connect Status. Shows the connect speed, connection type, and error correction being used.

DISCONNECT? Press the Enter button to force the modem to hang up. Same as the ATH command.

RINGING. A remote modem or caller is attempting to establish a connection. One option is available from this screen by pressing the ◊ button:

MANUAL ANSWER? Forces the modem to answer the phone. You can use this option to establish a connection if autoanswer is turned off (S0=0). Same as the ATA command.

Multi-Tech Systems, Inc. MT5600BA/BL Series User Guide

22

 

Page 21 Page 23
Image 22
Page 21 Page 23
Contents MT5600BA/BL Series Revision Date Description Table of Contents Contents General Description and Features Telephone systems Installation Wall jack$#%#8. Click Finish to exit +,-./0$1Chapter 2 Installation 345 Using the Front Panel Using the Front Panel Front panelTrunks LimbsTwigs Limbs Branches Twigs From previous Limbs Branches Twigs Using the Front Panel Limb Branches Twigs Using the Front Panel Using the Front Panel Multi-Tech Systems, Inc. MT5600BA/BL Series User Guide Using the Front Panel Using the Front Panel Using the Front Panel Ters, press the 〈 and  buttons. To go to the next position Using the Front Panel Leased Line Operation Leased Line Operation Leased Line Operation Leased Line Operation Remote Configuration Modem you must use the new password Remote ConfigurationCallback Security Available Callback SecurityIng strings have been entered Callback Security Callback Enable/Disable # Callback Security Troubleshooting Troubleshooting Troubleshooting Assistance see Appendix DTroubleshooting Troubleshooting Troubleshooting Appendix a Regulatory Compliance Appendix a Regulatory Compliance Modem to become non-compliant Exceed Error Correction CommandsCommand Buffer Mode of OperationDiagnostics Appendix B Technical SpecificationsConnectors IndicatorsAppendix C Warranty,Service, and Technical Support Sep-01 Appendix C Warranty, Service, and Technical Support DEFAULT.ASPEtc Restore your parameters Not 6.xx firmware Close the terminal program Com4 ttyS3 Using the Modem to Call the Internet Appendix E Installing a Modem Under LinuxAppendix F Pin Descriptions Appendix F Pin Descriptions RDLFig. F-4. Two-wire leased line cable Index IndexSerial cable Windows
Top Page Image Contents