Multi-Tech Systems MT5634ZPX-PCI-V92 manual If Dial-Up Networking is already installed

Page 17

MultiModemZPX User Guide

2 Installation

6.In the Configure Port Usage dialog box, select Dial out only, Receive calls only, or Dial out and receive calls, depending upon how the phone line will be used. Click OK.

7.In the Remote Access Setup dialog box, click Network.

8.In the Network Configuration dialog box, make sure that only TCP/IP is select- ed, and then click OK.

9.If there is a network interface card that does not have TCP/IP bound to it, the Microsoft TCP/IP Properties window appears. Click Cancel to close the window.

10.Click Continue, and then click Restart to finish the installation.

11.After completing the hardware and driver installation, you must configure your modem for country-specific operation. See “Step 4: Configure the Modem for Your Country” for configuration instructions.

12.After setting up your modem for country-specific operation, you’ll want to con- figure your communications software or Windows Dial-Up Networking. Infor- mation about configuring your communications software can be found in Step 5.

If Dial-Up Networking is already installed

1.Double-click the My Computer icon, then the Control Panel icon, and then the Network icon.

2.In the Network dialog box, click the Services tab, and then double-click Remote Access Service.

3.In the Remote Access Setup dialog box, a list of modems is displayed. Click Add.

4.In the Add RAS Device dialog box, choose Multi-Tech Systems MT5634ZPX- PCI-V92, and then click OK.

5.In the Remote Access Setup dialog box, click Configure.

6.In the Configure Port Usage dialog box, select Dial out only, Receive calls only, or Dial out and receive calls, depending upon how the phone line will be used. Click OK.

7.In the Remote Access Setup dialog box, click Continue.

8.The system processes the new information and the Network Settings Change dialog box appears. Select Yes to restart your computer.

9.After completing the hardware and driver installation, you must configure your modem for country-specific operation. See “Step 4: Configure the Modem for Your Country” for configuration instructions.

10.After setting up your modem for country-specific operation, you’ll want to con- figure your communications software or Windows Dial-Up Networking. Infor- mation about configuring your communications software can be found in Step 5.

12

Image 17
Contents Page Record of Revisions Introduction Solving Problems Appendix G Installing Under SCO OpenServer Introduction Product Description What Is in Your Modem Package?Introduction Installation What You Will Need Safety WarningsWe supply You supplyInstall the MultiModemZPX in your Computer Phone Connection Make the External ConnectionsLine Connection Sound Card and Speaker Connections Microphone ConnectionWindows 98/Me Install the Modem DriverWindows Changing the Windows 95/98/Me COM port assignment Verifying the Windows 95/98/Me Configuration Windows NT If Dial-Up Networking is not installedIf Dial-Up Networking is already installed Verifying the Windows NT Configuration Viewing system resources Global Wizard Utility Configure the Modem for Your CountryAT Commands Install and Configure Your Software Operation Connecting to the Internet Configuring the ModemPhoneTools Features Sending a Fax Dial-Up NetworkingReferences AT Commands Registers Result Codes Introduction Repeat Last Command AT CommandsCommunication Standard Setting AnswerDS=n Dial Stored Telephone Number Echo Command Mode CharactersEcho Online Data Characters Hook ControlReturn Online to Data Mode Monitor Speaker ModeResult Codes Enable/Disable Modulation HandshakeTone Dialing Modem ResetResult Code Format Result Code OptionsAsynchronous Communications Mode Load Factory SettingsData Terminal Ready DTR Control XON/XOFF Pacing ControlDisplay Current Settings Test CommandsStore Current Configuration Store Dialing Command\Kn Break Control \Bn Transmit Break\Jn Data Buffer Control \Tn Inactivity Timer \Nn Error Correction Mode Selection\Qn Flow Control Selection \V n Protocol Result CodeData Calling Tone Adaptive Answer Result Code EnableView Numbers in Blacklist 42bis Compression ControlData Compression Reporting Command +DCS=x,y Select V.44 Data CompressionCommand +DS44=n V.44 Data Compression Subparameters Enable Synchronous Buffered ModeMod Modulation SelectionCommand +PCW= n Call Waiting Enable Command +PMHR=n Modem on Hold Initiate Modem on Hold EnablePCM Upstream Ignore Modem Hook FlashQuick Connect Control Command +PMHT=n Modem on Hold TimerCommand +VDR=x, y Distinctive Ring Report Command +VCID=n Caller ID Selection#Sx Enter Setup Password #S=x Store Setup PasswordCommand %%%ATCR Remote Configuration Escape Sequence Command +++ATCR Escape SequenceRegisters Register Unit Range Default DescriptionValue Rate Value SpeedValue Digital loss Bit 56K modeTerse Verbose Description Result CodesDelayed Remote Configuration To Change the Setup Password Basic ProcedureSetup To Change the Remote Escape Character Solving Problems Modem Does Not Respond to Commands Modem Cannot Connect When Dialing ModemDisconnects While Online MultiModemZPX User Guide Modem Doesn’t Work with Caller ID There Are Garbage Characters on the MonitorFax and DataSoftware Can’t Run at the Same Time Voice Functions Don’t WorkSpeakerphone Test Voice Mail TestLoopback Test Appendixes FCC Part 68 Telecom Appendix a Regulatory ComplianceFax Branding Statement FCC PartProtection Against Contact with TNV Circuit Canadian Limitations NoticeIndustry Canada New Zealand Telecom Warning Notice EMC, Safety, and R&TTE Directive ComplianceInternational Modem Restrictions South African NoticeAppendix B Technical Specifications Command Buffer Local Analog Loopback Test V.54 Loop Test procedureFigure C-2. Remote digital loopback test Remote Digital Loopback Test V.54 LoopFigure C-3. Local digital loopback test Local Digital Loopback Test V.54 LoopMultiModemZPX User Guide Loopback Tests Canadian Customers Limited WarrantyOnline Warranty Registration Service International Distributors International Customers outside U.S.A. and CanadaInternet Sites Technical SupportIdentify the Modem Firmware Upgrade OverviewExtract the Upgrade Files Download the Upgrade FileIdentify the Current Firmware Version Document and Clear Your Stored ParamentersRestore Your Parameters Upgrade the Modem’s FirmwarePC port Linux port InstallationStandard Linux Serial Port Definitions Using the Modem to Call the Internet Using the Terminal Program Minicom to Verify OperationAnswering Calls Calling the ISPAppendix G Installing Under SCO OpenServer Index MultiModemZPX User Guide Index MultiModemZPX User Guide Index MultiModemZPX User Guide Index

MT5634ZPX-PCI-V92 specifications

The Multi-Tech Systems MT5634ZPX-PCI-V92 is a high-performance V.92 data/fax modem designed to enhance communication capabilities in various applications. This modem is particularly well-suited for commercial and industrial environments where reliable connectivity is crucial.

One of the standout features of the MT5634ZPX-PCI-V92 is its support for the V.92 protocol, which allows for quicker uploads and improved connection speeds compared to earlier standards. It offers download speeds of up to 56 Kbps and upload speeds of up to 48 Kbps, making it an excellent choice for businesses that rely on time-sensitive data transmission. The modem's ability to maintain reliable connections even over noisy telephone lines is a critical aspect of its design, ensuring that users can depend on it for essential communications.

The MT5634ZPX-PCI-V92 also includes advanced error correction and data compression technologies, such as MNP 4 and V.42bis. These technologies work together to ensure data integrity during transfers and to maximize throughput, enabling users to send larger files without compromising quality or speed. Additionally, the modem features a robust fax capability, supporting both analog and digital fax transmissions, which is vital for businesses that frequently deal with document sharing.

A notable characteristic of the MT5634ZPX-PCI-V92 modem is its PCI interface, which allows for easy integration into desktop systems. This plug-and-play capability simplifies installation and setup, making it accessible for users with varying levels of technical expertise. The modem is built on a reliable hardware platform, characterized by its durable components, making it ideal for environments where long-term use is expected.

Moreover, the MT5634ZPX-PCI-V92 comes with comprehensive driver support for various operating systems, including Windows and Linux, ensuring compatibility with a wide range of applications. With its combination of speed, reliability, and ease of use, the Multi-Tech Systems MT5634ZPX-PCI-V92 modem remains a popular option for businesses looking to maintain effective communication channels through dial-up connectivity. Whether for data transmission or faxing, it stands as a solid choice for organizations that require dependable performance in a compact form factor.