Multi-Tech Systems MT5634ZPX-PCI-V92 manual Result Codes, Terse Verbose Description

Page 48

MultiModemZPX User Guide

4 AT Commands, S-Registers, and Result Codes

Result Codes

In command mode your modem can send responses called result codes to your com- puter. Result codes are used by communications programs and can also appear on your monitor.

Terse

Verbose

Description

0

OK

Command executed

1

CONNECT

Modem connected to line

2

RING

Ring signal detected

3

NO CARRIER

Carrier signal lost or not detected

4

ERROR

Invalid command

5

CONNECT 1200 *

Connected at 1200 bps

6

NO DIALTONE

No dial tone detected

7

BUSY

Busy signal detected

8

NO ANSWER

No answer at remote end

10

CONNECT 2400 *

Connected at 2400 bps

11

CONNECT 4800 *

Connected at 4800 bps

12

CONNECT 9600 *

Connected at 9600 bps

13

CONNECT 14400 *

Connected at 14400 bps

14

CONNECT 19200 *

Connected at 19200 bps

24

CONNECT 7200 *

Connected at 7200 bps

25

CONNECT 12000 *

Connected at 12000 bps

26

CONNECT 16800 *

Connected at 16800 bps

40

CONNECT 300 *

Connected at 300 bps

55

CONNECT 21600 *

Connected at 21600 bps

56

CONNECT 24000 *

Connected at 24000 bps

57

CONNECT 26400 *

Connected at 26400 bps

58

CONNECT 28800 *

Connected at 28800 bps

59

CONNECT 31200 *

Connected at 31200 bps

60

CONNECT 33600 *

Connected at 33600 bps

70CONNECT 32000 * Connected at 32000 bps, 56K rate

71CONNECT 34000 * Connected at 34000 bps, 56K rate

72CONNECT 36000 * Connected at 36000 bps, 56K rate

73CONNECT 38000 * Connected at 38000 bps, 56K rate

74CONNECT 40000 * Connected at 40000 bps, 56K rate

75CONNECT 42000 * Connected at 42000 bps, 56K rate

76CONNECT 44000 * Connected at 44000 bps, 56K rate

77CONNECT 46000 * Connected at 46000 bps, 56K rate

78CONNECT 48000 * Connected at 48000 bps, 56K rate

79CONNECT 50000 * Connected at 50000 bps, 56K rate

80CONNECT 52000 * Connected at 52000 bps, 56K rate

81CONNECT 54000 * Connected at 54000 bps, 56K rate

82CONNECT 56000 * Connected at 56000 bps, 56K rate

*When the extended result code configuration option is enabled, one of the following codes is append- ed to the result code, depending on the type of error control connection:

V42bis – V.42 error control (LAP-M) and V.42bis data compression V42 – V.42 error control (LAP-M) only

MNP5 – MNP 4 error control and MNP 5 data compression MNP4 – MNP 4 error control only

NoEC – No error control protocol

43

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Page Record of Revisions Introduction Solving Problems Appendix G Installing Under SCO OpenServer Introduction What Is in Your Modem Package? IntroductionProduct Description Installation Safety Warnings What You Will NeedWe supply You supplyInstall the MultiModemZPX in your Computer Make the External Connections Line ConnectionPhone Connection Microphone Connection Sound Card and Speaker ConnectionsInstall the Modem Driver WindowsWindows 98/Me Changing the Windows 95/98/Me COM port assignment Verifying the Windows 95/98/Me Configuration If Dial-Up Networking is not installed Windows NTIf Dial-Up Networking is already installed Verifying the Windows NT Configuration Viewing system resources Configure the Modem for Your Country AT CommandsGlobal Wizard Utility Install and Configure Your Software Operation Configuring the Modem PhoneTools FeaturesConnecting to the Internet Dial-Up Networking Sending a FaxReferences AT Commands Registers Result Codes Introduction AT Commands Repeat Last CommandCommunication Standard Setting AnswerEcho Command Mode Characters DS=n Dial Stored Telephone NumberEcho Online Data Characters Hook ControlMonitor Speaker Mode Return Online to Data ModeResult Codes Enable/Disable Modulation HandshakeModem Reset Tone DialingResult Code Format Result Code OptionsLoad Factory Settings Asynchronous Communications ModeData Terminal Ready DTR Control XON/XOFF Pacing ControlTest Commands Display Current SettingsStore Current Configuration Store Dialing Command\Bn Transmit Break \Jn Data Buffer Control\Kn Break Control \Nn Error Correction Mode Selection \Tn Inactivity Timer\Qn Flow Control Selection \V n Protocol Result CodeAdaptive Answer Result Code Enable Data Calling ToneView Numbers in Blacklist 42bis Compression ControlCommand +DCS=x,y Select V.44 Data Compression Command +DS44=n V.44 Data CompressionData Compression Reporting Enable Synchronous Buffered Mode SubparametersModulation Selection ModCommand +PCW= n Call Waiting Enable Modem on Hold Enable Command +PMHR=n Modem on Hold InitiatePCM Upstream Ignore Modem Hook FlashCommand +PMHT=n Modem on Hold Timer Quick Connect ControlCommand +VCID=n Caller ID Selection Command +VDR=x, y Distinctive Ring Report#Sx Enter Setup Password #S=x Store Setup PasswordCommand +++ATCR Escape Sequence Command %%%ATCR Remote Configuration Escape SequenceRegister Unit Range Default Description RegistersValue Speed Value RateBit 56K mode Value Digital lossResult Codes Terse Verbose DescriptionDelayed Remote Configuration Basic Procedure SetupTo Change the Setup Password To Change the Remote Escape Character Solving Problems Modem Does Not Respond to Commands Modem Cannot Connect When Dialing ModemDisconnects While Online MultiModemZPX User Guide There Are Garbage Characters on the Monitor Modem Doesn’t Work with Caller IDFax and DataSoftware Can’t Run at the Same Time Voice Functions Don’t WorkVoice Mail Test Loopback TestSpeakerphone Test Appendixes Appendix a Regulatory Compliance FCC Part 68 TelecomFCC Part Fax Branding StatementCanadian Limitations Notice Industry CanadaProtection Against Contact with TNV Circuit EMC, Safety, and R&TTE Directive Compliance New Zealand Telecom Warning NoticeSouth African Notice International Modem RestrictionsAppendix B Technical Specifications Command Buffer Test procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback testLocal Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback testMultiModemZPX User Guide Loopback Tests Limited Warranty Online Warranty Registration ServiceCanadian Customers International Customers outside U.S.A. and Canada International DistributorsTechnical Support Internet SitesUpgrade Overview Identify the Modem FirmwareDownload the Upgrade File Extract the Upgrade FilesIdentify the Current Firmware Version Document and Clear Your Stored ParamentersUpgrade the Modem’s Firmware Restore Your ParametersInstallation Standard Linux Serial Port DefinitionsPC port Linux port Using the Terminal Program Minicom to Verify Operation Using the Modem to Call the InternetCalling the ISP Answering CallsAppendix G Installing Under SCO OpenServer Index MultiModemZPX User Guide Index MultiModemZPX User Guide Index MultiModemZPX User Guide Index

MT5634ZPX-PCI-V92 specifications

The Multi-Tech Systems MT5634ZPX-PCI-V92 is a high-performance V.92 data/fax modem designed to enhance communication capabilities in various applications. This modem is particularly well-suited for commercial and industrial environments where reliable connectivity is crucial.

One of the standout features of the MT5634ZPX-PCI-V92 is its support for the V.92 protocol, which allows for quicker uploads and improved connection speeds compared to earlier standards. It offers download speeds of up to 56 Kbps and upload speeds of up to 48 Kbps, making it an excellent choice for businesses that rely on time-sensitive data transmission. The modem's ability to maintain reliable connections even over noisy telephone lines is a critical aspect of its design, ensuring that users can depend on it for essential communications.

The MT5634ZPX-PCI-V92 also includes advanced error correction and data compression technologies, such as MNP 4 and V.42bis. These technologies work together to ensure data integrity during transfers and to maximize throughput, enabling users to send larger files without compromising quality or speed. Additionally, the modem features a robust fax capability, supporting both analog and digital fax transmissions, which is vital for businesses that frequently deal with document sharing.

A notable characteristic of the MT5634ZPX-PCI-V92 modem is its PCI interface, which allows for easy integration into desktop systems. This plug-and-play capability simplifies installation and setup, making it accessible for users with varying levels of technical expertise. The modem is built on a reliable hardware platform, characterized by its durable components, making it ideal for environments where long-term use is expected.

Moreover, the MT5634ZPX-PCI-V92 comes with comprehensive driver support for various operating systems, including Windows and Linux, ensuring compatibility with a wide range of applications. With its combination of speed, reliability, and ease of use, the Multi-Tech Systems MT5634ZPX-PCI-V92 modem remains a popular option for businesses looking to maintain effective communication channels through dial-up connectivity. Whether for data transmission or faxing, it stands as a solid choice for organizations that require dependable performance in a compact form factor.
Top Page Image Contents