Multi-Tech Systems MT2456SMI22 manual Product Safety and EMC Approvals, Country Certifications

Page 48

Appendix B – Product Approvals, Regulatory Design Considerations, Compliance

Appendix B - Product Approvals,

Compliance, and Layout

Considerations

Product Safety and EMC Approvals

Safety	EMC
UL 60950	FCC Part 15 (Class B)
CSA 950	Canada (Class B)
EN 60950	EN 55022 (Class B)
AS 3260	EN 55024

Country Certifications

While this device can be configured for specific country operation, doing so DOES NOT constitute country approval. This modem is not approved in or configured for operation in all countries. The following list is displays the country approvals as of April 1, 2003.

This information can be deemed reliable, but is not guaranteed. All information is subject to change. Contact your Multi-Tech Systems, Inc. sales representative or call the world headquarters at 800-328-9717.

Country	Country Code
US	B5
Canada	B5
Austria	B5
Belgium	B5
Cyprus	B5
Denmark	B5
Finland	B5
France	B5
Germany	B5
Greece	B5
Iceland	B5
Ireland	B5
Italy	B5
Liechtenstein	B5
Luxembourg	B5
Netherlands	B5
Norway	B5
Portugal	B5
Spain	B5
Sweden	B5
Switzerland	B5
UK	B5
More planned.

Note: See the AT+GCI command. Reporting uses of this command will show you the current country code and the country profiles stored in the modem’s ROM.

Multi-Tech Systems, Inc. MT2456SMI-22 SocketModem Developer’s Guide

48

Image 48

Contents SocketModem PN S000281A, Version a Country By Email By PhoneContents Product Description Specifications Product DescriptionTechnical Specifications Speed ConversionPhysical Dimensions Maximum Component HeightPin Configurations Pin Descriptions3V DC Power Handling Precautions 3V and 5V Serial SocketModemInput High Input Low Outputs Output High Output LowGeneric Modem Control Commands DTE/DCE CommandsCall Control Commands Modulation Control CommandsError Control and Data Compression Commands Synchronous Access Mode CommandsFast Connect Command Line Side Device Commands22bis Generic Modem Control Commands Soft Reset and Restore ProfileOperating Mode +VCID Caller ID CID+GCI Country of Installation IdentificationRestore Factory Configuration Profile ProcedureLocal Analog Loopback Test Load to Internal RAM22bis DTE/DCE-Modem Interface commands Command EchoQuiet Result Codes Control Result Code FormConnect Ring No Carrier Error No Dial Tone Busy No Answer Extended Result CodesShort Form Long Form Value in ATXn Command Rlsd OptionResult Codes OK 0 or DTR OptionRTS/CTS Option \G Modem-to-Modem Flow Control XON/XOFF+IFC DTE-Modem Local Flow Control +IBC In Band Commands Entering and Exiting In Band Active StateEM Shielding Data Command Hex Codes Description Supported DTE-to-DCE Commands Supported DCE-to-DTE CommandsBand Processing of AT Commands 22bis Call Control Commands DialDial Modifiers Set Tone Dial Default Result Code Set Pulse Dial DefaultReturn to On-Line Data Mode Speaker VolumeDisplay Current Configuration and Stored Profiles MSpeaker ControlSelect Guard Tone Select Pulse Dial Make/Break Ratio\V Single Line Connect Message Enable Report Line Signal LevelReport Line Signal Quality Display Blacklisted NumbersDisplay Delayed Numbers NO. Phone Number -DELAYBehavior in Data Mode Syntax *D Example+PCW Call Waiting Enable Reporting Selected Values+VDR Distinctive Ring 22bis Modulation Control Commands Table of +MS Command Supported Rates+MS Modulation Selection SyntaxEnable/Disable Line Quality Monitor and Auto-Retrain ITU-T or Bell22bis Error Control and Data Compression Commands +ESR Selective Repeat+ETBM Call Termination Buffer Management \B Transmit Break to RemoteResult Codes OK 0 to 5 Error Otherwise Break Control22bis Synchronous Access Mode Commands +ESA Configure Synchronous Access SubmodeReporting Selected Options +ESA?Transmit Flow Control Thresholds +ITF?22bis FastConnect Command $F Fast Connect ControlSyntax $Fn Defined Values 22bis Line Side Device Commands Threshold Adjustments for Telephony ExtensionTRV Tip and Ring Voltage Measurement Response22bis S-Parameters Read/Write S-ParameterSummary of S-Parameter Defaults Register Function Range/Units DefaultAscii S0 Number of Rings to Auto-Answer S1 Ring CounterS2 Escape Character S3 Carriage Return CharacterS8 Pause Time For Dial Delay S10 Lost Carrier To Hang Up DelayS12 Escape Prompt Delay EPD S9 Carrier Detect Response TimeS16 Test Mode Bit Mapped Options Status S19 ReservedS20 Reserved S21 V.24/General Bit Mapped Options StatusS24 Sleep Inactivity Timer S25 Delay To DTR OffS26 RTS to CTS Delay S22 Speaker/Results Bit Mapped Options StatusS30 Disconnect Inactivity Timer S27 Bit Mapped Options StatusS28 Bit Mapped Options Status S29 Flash Dial Modifier TimeS38 Delay Before Forced Hang Up S36 Lapm Failure ControlS37 Desired Line Connection Speed S39 Flow Control Bit Mapped Options StatusS41 General Bit Mapped Options Status S48 V.42 Negotiation ActionS82 Break Handling Options S86 Call Failure Reason CodeS91 Pstn Transmit Attenuation Level S95 Extended Result Codes Control 22bis Result Codes Table of Result Code Definitions Code Message Meaning Connect75TX/1200RX Is enabled Block Diagram Figure A-1. Serial Test/Demo Board Block DiagramProduct Safety and EMC Approvals Country CertificationsCountry Country Code More plannedRegulatory Design Considerations Hardware ConsiderationsSafety SocketModem Placement Qty Name DescriptionCompliance Multi-Tech Systems, Inc. ComplianceTelecom Requirements for the United States Label Content and Format Label Physical CharacteristicsTelecommunications Regulations for Canada Labeling Continuity and ChangesOther Label Requirements New Zealand Telecom Warning Notice Industry CanadaEMC, Safety, and R&TTE Directive Compliance International Modem RestrictionsSouth African Statement Index Index