MGE UPS Systems 66846, 66244, 66074 user manual Network Settings

Page 31

www.mgeups.com

Network

Management Cards

User Manual

3.5.1Network Settings

Click on the “Network” section in the menu.

This menu enables the administrator to configure the network parameters of the card and authorisation of the remote upgrade of the embedded system.

ZIP address: The IP address of the card (e.g.: 172.17.23.205).

ZSubnet Mask: The mask of the sub-network of your network (e.g.: 255.255.255.0).

ZGateway Address: Indicate the IP address of the gateway to access the stations located outside the

card’s sub-network (e.g.: 172.17.1.24).

ZHostname must be suited to the card. This is the first part of the full qualified domain name, used by the

DNS (name must be compatible with DNS rules)

ZDomain name is the domain to which the card belongs. This is the part of the full qualified domain name that follows the host name and is used by the DNS. The default value of the two parameters comprising the full qualified domain name: ups.domain.com

ZTELNET connection: Authorises (choose enable) remote connection with a terminal to access the maintenance menu.

See “Configuration in local mode and via Telnet “ for more information

ZBootP/DHCP: Authorises (choose enable) configuration of network parameters with your BootP/DHCP server when the card is booted

T H E U N I N T E R R U P T I B L E P O W E R P R O V I D E R

Network Management Card – User Manual

34003676EN/GA

Page 31/69

Image 31

Contents E U N I N T E R R U P T I B L E P O W E R P R O V I D E R Network Management Cards Table of ContentsAPPENDICES63 Tables of Alarms and Events ConfigurationConfiguration VIA Telnet Configuration VIA SSH Maintenance Software UPGRADE62Network Management Card or Proxy MGE Network SolutionConnecting the UPS to the Network IntroductionNetwork Shutdown module MGE supervisor Enterprise Power ManagerProtecting the computers / servers Monitoring the UPSs over the networkConnection Presentation of the Environment Sensor solutionHow to connect UPS / agent / network Setting up the protectionDirect sending of E-mail Compatibility with the legacy Solution-Pac WAN offeringSending text messages SMS Technical data 9/69 Environment Sensor Installation and ConfigurationInstallation Basic configurationOptimising the performance of your browser Supervision / Administration via a Web browserUPS status zone essential information UPSUPS properties UPS zone general information on the UPSBattery status zone On-line help Normal input measurements 3 3-Phase displayUPS Control Battery measurementsBy Pass measurements 17/69 UPS weekly schedule programming Important note Shutdown parameters20/69 Viewing the alarms Measurements Logs23/69 Event log System log Email Notification NotificationNotified events Recipient List Mail message configuration see next Sender Email Message Settings Subject 29/69 User Name and password by default are Mgeups ConfigurationNetwork Settings 32/69 System 34/69 Notified Applications Central Shutdown Configuration Access control 38/69 SSL Time Status Configuration Log CharacteristicsEnvironment Environment status Humidity Environment Settings4 Log Set-up of the shutdown parameters Servers protectionShutdown criteria managed by the Management Card Shutdown duration Specific set-up for long autonomy installation 30 mnShutdown when backup time is less than Controlled outletsSequential startup Load shedding or sequential shutdownMain UPS outlet Different server and UPS shutdown sequencesProgrammable outlet 49/69 2.2 Programmable outlet 2.1 Main UPS outlet2.3 Programmable outlet 51/69 3.2 Programmable outlet 3.1 Main UPS outletNetwork Main outlet 4 Off/On command55/69 Configuration in local mode and via Telnet or SSH Configuring a set of cards with MupgradeConfiguration in local mode Mgeups Choice 1 Snmp agent configuration menuChoice 2 UPS parameters Choice 3 Access controlChoice 5 Reset the card Choice 4 Restore default configurationConfiguration via SSH Configuration via TelnetPuTTY SSH Client Program 61/69 Card software upgrade via Tftp Unix and Windows MaintenanceSoftware upgrade Card firmware upgrade using Mupgrade WindowsUPS event table Tables of alarms and eventsAlarm table AppendicesUPS 65/69 English French System alarm tableGlossary Subnet mask Programmable outlet controlled outletTelnet UM-Client Trap Snmp