Liebert 1000 - 3000VA 60 Hz 120V External Battery Cabinet Installation, Repo switch connections

Page 19

Installation

Figure 11 REPO switch connections

REPO Connection

REPO Switch

REPO connections

REPO connections

as shipped

for normally open

for normally closed

 

 

 

 

switch system

switch system (fail-safe)

1

2

3

4

1

2

3

4

1

2

3

4

Key to REPO switch connections

1.24 VDC,

2.Sense

3.Sense

4.Ground

5.4External Battery Cabinet Installation

Optional Liebert external battery cabinets may be connected to the UPS to provide additional battery run time. External battery cabinets are designed to be placed all on one side of the UPS or stacked beneath the UPS. The run time is limited to a maximum of four (4) hours.

! CAUTION

The external battery cabinet(s) are heavy (see 12.0 - Specifications). External battery cabinets can be used in rack-mount or tower configuration. Take proper precautions when lifting them.

1.Visually inspect the external battery cabinet for freight damage. Report damage to the carrier and your local dealer or Liebert representative.

2.The rack-mount handles are shipped with the external battery cabinet and may be installed at this time (see 5.3 - Rack-Mount UPS Conversion and Installation).

3.Fixed rails and securing hardware ship with the external battery cabinet. Fasten the fixed rails into position with the screws per the instructions included with the UPS. Repeat

Steps 1 through 10 from 5.3 - Rack-Mount UPS Conversion and Installation.

4.Use the support bases included with the UPS for the tower option to prevent tip-over. One additional set of support base spacers ships with each external battery cabinet.

5.Connect the supplied external battery cabinet cable to the rear of the external battery cabinet, then to the rear of the UPS, as shown at right.

BATTERY

BATTERY

CONNECTOR

CONNECTOR

1440VA/DC 48V/30A

1440VA/DC 48V/30A

1000VA/DC 48V/20A

1000VA/DC 48V/20A

6.The UPS is now equipped with additional backup battery run time. For approximate battery run times, refer to Table 5 - Battery run times.

1

REPO

3

2

 

4

 

 

RS-232

INTELLISLOT

IN OUT

BATTERY

CONNECTOR

1440VA/DC 48V/30A

1000VA/DC 48V/20A

PHONE / FAX / MODEM / NETWORK

LOAD 2

LOAD 1

PROTECTION

 

+

INPUT

 

 

-

 

 

INPUT

 

 

BREAKER

 

 

PUSH TO RESET

 

 

13

Image 19
Contents Liebert PowerSure PSI Page Table of Contents Communications Product Warranty RegistrationFigures Page Safety Precautions Important Safety InstructionsBattery Handling Precautions Glossary of Symbols Front view of UPS Introduction3000VA PSI-rear view Major Components RelayInverter-1000/1440 Models Only Battery ChargerBattery Automatic Voltage RegulatorWHAT’S Included Installation Tower UPS InstallationPreparation Rack mount handles Rack-Mount UPS Conversion and InstallationRack mounting rails and slide assemblies Option 1 Serial Communications Repo switch connections External Battery Cabinet InstallationControls and Indicators ON/Alarm Silence/Battery Test ButtonOFF Button Buck/Boost Indicator-Green Load Level Indicators-4 green, 1 amberBattery Level Indicators-5 green AC Input Indicator-GreenFault Indicator-Red Over Temp Indicator-AmberBuck/Boost Mode Normal ModeModes of Operation Battery Recharge Operation Battery ModeRemote Shutdown Via the DB-9 Connector DB-9 ConnectorCommunications USB Interface Port Data Line Protection ConnectorsUPS Intelligent Communications Utility power will be applied to the connected load Voltage Programming ProcedureMaintaining Batteries Cleaning the UPSBattery Replacement MaintenanceInternal Battery Replacement Procedure Status indicators TroubleshootingTroubleshooting chart Problem Cause Solution UPS specifications SpecificationsBattery cabinet specifications Battery run times Product Warranty Registration Site Nic

1000 - 3000VA 60 Hz 120V specifications

The Liebert 1000 - 3000VA 60 Hz 120V is an uninterruptible power supply (UPS) designed to protect critical electronic equipment and ensure uninterrupted operation in various settings. Ideal for small to medium-sized businesses, the Liebert UPS offers reliable power protection with its compact and efficient design.

One of the main features of the Liebert 1000 - 3000VA is its advanced battery technology. Equipped with high-performance sealed lead-acid batteries, this UPS ensures long-lasting power backup while requiring minimal maintenance. The smart battery management system intelligently monitors battery health, extending overall battery life while providing precise notifications for replacement, thus optimizing operational efficiency.

Another critical characteristic is its online double-conversion technology. This feature provides consistent and clean power by converting incoming AC power to DC and then back to AC again. This process effectively eliminates any electrical noise or power fluctuations, protecting sensitive electronics from interruptions or damage caused by power surges, spikes, or drops. As a result, workloads can operate without concern for potential power issues.

The Liebert UPS is designed with user-friendliness in mind. Featuring a clear LED display, it allows users to easily monitor performance metrics such as load level, battery health, and runtime status. In addition, the intuitive control panel simplifies operation and navigation through settings, making it accessible to users without extensive technical knowledge.

This UPS also offers flexibility with multiple outlet options. The Liebert 1000 - 3000VA includes a combination of NEMA outlets, providing compatibility with various equipment types, from servers and routers to networking devices and communications equipment. This versatility ensures that it meets diverse power requirements within any environment.

Moreover, the compact form factor enables installation in tight spaces while maintaining robust performance. Its efficient design facilitates heat dissipation, ensuring optimal operation without overheating.

The Liebert 1000 - 3000VA 60 Hz 120V UPS delivers excellent protection for critical equipment across various industries, including telecommunications, healthcare, and finance, ensuring operational continuity. With its advanced features, reliable technologies, and user-centered design, it stands out as a reliable choice for any organization seeking to safeguard its power supply infrastructure.