GarrettCom manual Connecting the Console Terminal to Magnum 6K25 Management, Console DB-9 Port

Page 41

Magnum 6K25 Managed Fiber Switch

Installation and User Guide (04/06)

Step 3. Remove 6KPM Card

Carefully and gently pull

out the daughter board from the latching connectors, using both hands, gripping the board near the latch-up connectors as shown in Fig. 3.5.3b . If the now empty slot is to remain unused, be sure to install

a6KPM-BLNK face plate cover.

Figure 3.5.3b: Removing a 6KPM Card

If another 6KPM card is replacing the one that has been removed, follow the steps as described for installing a 6KPM card discussed in Section 3.5.1.

3.6Connecting the Console Terminal to Magnum 6K25 (Management)

Use a DB-9 “null modem” cable to connect the Magnum6K25 Console Port (the RS-232 port on the 6K25 Switch) to the your PC, so that your PC becomes the 6K25’s Console Terminal.

Note: The DB-9 cable does not include with the 6K25 unit package.

Console (DB-9)

Port

CONSOLE

PORT

O

OF

Rear View of Magnum 6K25, (Typical Console Port is on the Rear of Reverse 6K25 Models)

Note: For detail description of Managed Network Software (MNS-6K) and Magnum 6K25 Switch configuration for Network Management, please refer to Magnum 6K25 Software Manual available on GarrettCom‘s FTP site. Detail info. about the MNS is available on 2.2.9 ( see page no. 13) of this manual.

www . GarrettCom . com

34

Image 41
Contents Managed Fiber Switch Trademarks Canadian Emission Contacting GarrettCom, IncIntroduction Table of ContentsRevisions TroubleshootingWww . GarrettCom . com Media Converters, 10Mb and 100Mb series Personal Switches , 10/100MbPersonal Hubs, 10Mb series Performance Technical SpecificationsNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsManagement Console connector Fiber Single-mode connector typesPower Supply Internal DC Power Supply OptionsNebs Testing and Certification Nebs certified Alarm Contact OptionalPer-port MDI or Mdix on RJ-45 Agency ApprovalsOrdering Information 6K PoE Modules with 48VDC Pass-Through For Gigabit module configuration options6K PoE Modules with 48VDC Power Inside Introduction Inspecting the Package and Product Product Description Magnum 6K25 Managed Fiber Switch Magnum 6K25 and 6K25R chassis 1a Regular 6K25 front view, configured for 24 +1 Gb portsEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 The 6K25-Series’s8-port New PoEPower Inside, model PI6KP8-45RJ MDIX, 10/100Mb 8-port ACT LK RX Gigabit 1000Mbps port modules Four-Port 10 Mb mm Fiber ST Modules@ 1000Mb Fiber SC + 4@10/ 100Mb Packet Prioritization, 802.1p QOSFrame Buffering and Flow Control GarrettCom proprietary MIBs for Snmp Managed Network Software MNS-6K for Magnum 6K25-Series„ Features Fiber-Built-In „ Managed switching for high performance Ethernet LANs„ RJ-45 ports are MDI/MDIX supported „ Nebs and Etsi tested and certifiedApplications Example 1 Magnum 6K25 Switch for a Vlan applicationInternet Locating Magnum 6K25 Switches InstallationConnecting Fiber Optic ST-type, twist-lock Connecting Ethernet MediaIeee Standard Media Type Max. Distance Port Module Fiber CopperConnecting Single-Mode Fiber Optic Connecting Fiber Optic SC-type, Snap-InMedia Ieee Standard Media Ieee Standard ConnectorRack-mounting for 19 Retma racks, regular Magnum 6K25s Table-Top or Shelf Mounting2 Reverse Magnum 6K25 units, rack-mounted in a frame Rack-mounting, Reverse version of the Magnum 6K25sPowering the Magnum Managed Fiber Switch Remove Chassis Cover 6K25 Port Module 6KPM InstallationPreparation for Installing and Removing 6KPMs 1a Removing Chassis Cover Installing 6KPM Cards in the Magnum 6K25 Uplink 2f Securely latching up 6KPM Cards into a Magnum 6K25 Firmly. .5.3a Top View 6 retaining s crews shown by arrows Removing 6KPM CardsRemove 6KPM Card Connecting the Console Terminal to Magnum 6K25 ManagementConsole DB-9 Port 1 RS-232 DB-9 Console Com port Serial port pin assignments Pin Signal DescriptionDB-9PinConsole1port connector Address Learning Switching FunctionalityFiltering and Forwarding Up-link MDI-MDIX on RJ-45 port modules, for port 1 only Status LEDsAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports PWRWww . GarrettCom . com Flow-control, Ieee 802.3x standard ’cvr 6KP46KPM Module Description Introduction Magnum 6K25 Managed Fiber Switch Port ModulesSegments. When installed in a Mode ST-type connectorsSwitch, the copper port Dual speed copper ports.6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Mode SC-type connectors. It Provides an advantage Mode 100Mbps fiber opticFiber functions in one Module of the 6K25 Switch Transceivers all in one module. ThisWww . GarrettCom . com Link Port@ 100Mbps Multi-Mode Fiber portActivity FULL/HALF Module is a combo module with Magnum 6KP8-45MTCopper and fiber Small Form Factor Placing more ports on one module6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port PoE LEDs Summary Fig. the top 8-RJ45 6KP8-45-2SLC 14 6KM-BLNK GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC ConnectorBefore Calling for Assistance No Problem Found When Calling for AssistanceReturn Material Authorization RMA Procedure B1.0 Specifications for Magnum 6K25 SWITCHES, DC Power Appendix B Internal DC Power Supply OptionsPower Supply Internal -48VDC Option Shipping and Packaging InformationB3.0 Applications for DC Powered Switches Magnum 6K25s. see figure at right B4.0 InstallationB4.1 UL Requirements for DC-powered units B6.0 Ordering Information B7.0 TroubleshootingB5.0 Operation GND Appendix C Internal DC Dual-Source Power OptionC5.0 Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignC6.0 Ordering Information C5.1 UL RequirementsExample Magnum 6K25R-48VDC Example Magnum 6K25R-24VDC or Magnum 6K25R-125VDC
Related manuals
Manual 67 pages 19.91 Kb