GarrettCom manual C5.1 UL Requirements, C6.0 Ordering Information, Example Magnum 6K25R-48VDC

Page 68

Magnum 6K25 Managed Fiber Switch

Installation and User Guide (04/06)

C5.1 UL Requirements

The following must be adhered to in order to conform to UL requirements:

1.Minimum 18 AWG cable for connection to a Centralized DC power source.

2.Minimum 14 AWG cable for connection to earthing wiring.

3.Use only with Listed 10 A circuit breaker provided in building installation.

4.“Complies with FDA radiation performance standards, 21 CFR subchapter J.” or equivalent.

5.Fastening torque of the lugs on the terminal block: 9 inch pound max.

6.Centralized DC Power Source cable securement, use at least four cable ties to secure the cable to the rack at least 4 inches apart with the first one located within 6 inches of the terminal block.

C6.0 ORDERING INFORMATION

To order the optional Dual-Source -48VDC power supply factory installed, order “Dual-Src48V” as a separate line item following the product model.

Example: Magnum 6K25R-48VDC

Dual-Src-48Vfor the regular DS model with no ON-OFF switch or Dual-Src48V-SWITCHwith the ON-OFF manual switch.

Similarly, order the “Dual –source 24VDC” or “Dual-source 125VDC” as a separate line item following the product model.

Example: Magnum 6K25R-24VDC or Magnum 6K25R-125VDC

Dual-Src24Vfor regular models with no ON-OFF switch

Or Dual-Src125V-Switchfor models with the ON-OFF switch

C7.0 OPERATION

Operation of the Dual-Source Magnum 6Ks-48VDC, 24VDC and 125VDC Switch models are identical to that of the standard models.

www . GarrettCom . com

61

Image 68

Contents Managed Fiber Switch Trademarks Contacting GarrettCom, Inc Canadian EmissionTable of Contents IntroductionTroubleshooting RevisionsWww . GarrettCom . com Media Converters, 10Mb and 100Mb series Personal Switches , 10/100MbPersonal Hubs, 10Mb series Technical Specifications PerformanceNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsFiber Single-mode connector types Management Console connectorPower Supply Internal DC Power Supply OptionsAlarm Contact Optional Nebs Testing and Certification Nebs certifiedPer-port MDI or Mdix on RJ-45 Agency ApprovalsOrdering Information For Gigabit module configuration options 6K PoE Modules with 48VDC Pass-Through6K PoE Modules with 48VDC Power Inside Introduction Inspecting the Package and Product Product Description Magnum 6K25 Managed Fiber Switch 1a Regular 6K25 front view, configured for 24 +1 Gb ports Magnum 6K25 and 6K25R chassisEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 The 6K25-Series’s8-port New PoEPower Inside, model PI6KP8-45RJ MDIX, 10/100Mb 8-port ACT LK RX Four-Port 10 Mb mm Fiber ST Modules Gigabit 1000Mbps port modules@ 1000Mb Fiber SC + 4@10/ 100Mb Packet Prioritization, 802.1p QOSFrame Buffering and Flow Control Managed Network Software MNS-6K for Magnum 6K25-Series GarrettCom proprietary MIBs for Snmp„ Managed switching for high performance Ethernet LANs „ Features Fiber-Built-In„ Nebs and Etsi tested and certified „ RJ-45 ports are MDI/MDIX supportedExample 1 Magnum 6K25 Switch for a Vlan application ApplicationsInternet Installation Locating Magnum 6K25 SwitchesConnecting Ethernet Media Connecting Fiber Optic ST-type, twist-lockIeee Standard Media Type Max. Distance Port Module Fiber CopperConnecting Fiber Optic SC-type, Snap-In Connecting Single-Mode Fiber OpticMedia Ieee Standard Connector Media Ieee StandardTable-Top or Shelf Mounting Rack-mounting for 19 Retma racks, regular Magnum 6K25sRack-mounting, Reverse version of the Magnum 6K25s 2 Reverse Magnum 6K25 units, rack-mounted in a framePowering the Magnum Managed Fiber Switch Remove Chassis Cover 6K25 Port Module 6KPM InstallationPreparation for Installing and Removing 6KPMs 1a Removing Chassis Cover Installing 6KPM Cards in the Magnum 6K25 Uplink 2f Securely latching up 6KPM Cards into a Magnum 6K25 Removing 6KPM Cards Firmly. .5.3a Top View 6 retaining s crews shown by arrowsRemove 6KPM Card Connecting the Console Terminal to Magnum 6K25 ManagementConsole DB-9 Port 1 RS-232 DB-9 Console Com port Serial port pin assignments Pin Signal DescriptionDB-9PinConsole1port connector Address Learning Switching FunctionalityFiltering and Forwarding Status LEDs Up-link MDI-MDIX on RJ-45 port modules, for port 1 onlyAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports PWRWww . GarrettCom . com Flow-control, Ieee 802.3x standard 6KP4 ’cvrIntroduction Magnum 6K25 Managed Fiber Switch Port Modules 6KPM Module DescriptionMode ST-type connectors Segments. When installed in aSwitch, the copper port Dual speed copper ports.6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Mode 100Mbps fiber optic Mode SC-type connectors. It Provides an advantageFiber functions in one Module of the 6K25 Switch Transceivers all in one module. ThisWww . GarrettCom . com Link Port@ 100Mbps Multi-Mode Fiber portActivity FULL/HALF Magnum 6KP8-45MT Module is a combo module withCopper and fiber Small Form Factor Placing more ports on one module6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port PoE LEDs Summary Fig. the top 8-RJ45 6KP8-45-2SLC GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 14 6KM-BLNKBefore Calling for Assistance No Problem Found When Calling for AssistanceReturn Material Authorization RMA Procedure Appendix B Internal DC Power Supply Options B1.0 Specifications for Magnum 6K25 SWITCHES, DC PowerPower Supply Internal -48VDC Option Shipping and Packaging InformationB3.0 Applications for DC Powered Switches Magnum 6K25s. see figure at right B4.0 InstallationB4.1 UL Requirements for DC-powered units B6.0 Ordering Information B7.0 TroubleshootingB5.0 Operation Appendix C Internal DC Dual-Source Power Option GNDC4.0 Features and Benefits of the DUAL-SOURCE Design C5.0 InstallationC5.1 UL Requirements C6.0 Ordering InformationExample Magnum 6K25R-48VDC Example Magnum 6K25R-24VDC or Magnum 6K25R-125VDC

Related manuals

Manual 67 pages 19.91 Kb