GarrettCom manual 6K25 Port Module 6KPM Installation

Page 34

Magnum 6K25 Managed Fiber Switch

Installation and User Guide (04/06)

AC voltage is from 90 to 260 volts with a power input frequency between 47 and 63 Hz. The 25-port units will consume over 20 watts of power typically. When connecting the Ethernet cabling, there is no need to power down the unit. Individual segments can be connected or disconnected without concern for AC power-related problems or damage to the unit.

Power supply options are available to suit the 6K25 Switches to special high- availability communications and/or heavy industrial-grade applications, including:

*-48VDC, 24VDC and 125VDC with single DC input,

*-48VDC, 24VDC and 125VDC with dual-source DC input,

See the Appendices of this manual for more details. Use an RFQ for other variations.

3.4.1Alarm Contacts for monitoring internal power, and Software Traps

The Alarm Contacts feature, optional on Magnum 6K25’s, provides two

Form C Normally Closed (NC) contacts to which the user can attach two sets of status monitoring wires at the green terminal block. When this option is present, the terminal block for Alarm Contacts is part of the Power Input panel in the Magnum 6K25 case.

The AC or DC power input connection is in the same panel. A manual On-Off Switch for power to the unit is not available on 6K25 units with the Alarm Contacts option, as these two features occupy the same space in the case.

The first NC Alarm Contact (top position) is a “Software Alarm”, operated by user settings in the MNS-6K software. The user can disable the Software Alarm feature with a software configuration command if desired. When the Software Alarm is enabled, the Form C Normally Closed (NC) contact is held close during normal software operation. A user-defined software malfunction, such as an SNMP Trap or a Software Security violation or an S-Ring Fault, causes the contact to open and thus trigger an alarm in the user’s monitoring system

The second (bottom position) NC Alarm Contact is held close when there is power on the main board inside of the 6K25. This provides a “Hardware Alarm” because the NC contacts will open when internal power is lost, either from an external power down condition or by the failure of the power supply inside of the Magnum 6K25 Switch. Useful info. about Alarm contacts:

1.There is four terminal block (1,2,3,4)provided next to AC/DC power supply

2.The top two pins (1,2) are software operated

3.The bottom two pins (3,4) are hardware operated

4.By default it is NC (normally closed)

5.The software operation need to be enable and set to get the Alarm traps. For detail information about the Software Alarm and software control of SNMP alarm traps, please reference the Magnum MNS-6K Software User Manual. (Chapter 19th).

3.56K25 Port Module (6KPM) Installation

The Magnum 6K25 Switches are normally received from the factory with all

www . GarrettCom . com

27

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Managed Fiber Switch Trademarks Contacting GarrettCom, Inc Canadian EmissionSpecifications Troubleshooting Revisions Magnum Line Network Standards and Compliance, hardware Technical SpecificationsPerformance Maximum 10 Mbps Ethernet Segment LengthsManagement Console connector Fiber Multi-mode connector types supportedFiber Single-mode connector types Power Supply InternalPer-port MDI or Mdix on RJ-45 Alarm Contact OptionalNebs Testing and Certification Nebs certified Agency ApprovalsOrdering Information For Gigabit module configuration options 6K PoE Modules with 48VDC Pass-Through6K PoE Modules with 48VDC Power Inside Introduction Inspecting the Package and Product Product Description Magnum 6K25 Managed Fiber Switch 1a Regular 6K25 front view, configured for 24 +1 Gb ports Magnum 6K25 and 6K25R chassisEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 The 6K25-Series’s8-port New PoEPower Inside, model PI6KP8-45RJ MDIX, 10/100Mb 8-port ACT LK RX Four-Port 10 Mb mm Fiber ST Modules Gigabit 1000Mbps port modulesFrame Buffering and Flow Control Packet Prioritization, 802.1p QOS@ 1000Mb Fiber SC + 4@10/ 100Mb Managed Network Software MNS-6K for Magnum 6K25-Series GarrettCom proprietary MIBs for Snmp„ Managed switching for high performance Ethernet LANs „ Features Fiber-Built-In„ Nebs and Etsi tested and certified „ RJ-45 ports are MDI/MDIX supportedExample 1 Magnum 6K25 Switch for a Vlan application ApplicationsWww . GarrettCom . com Installation Locating Magnum 6K25 SwitchesIeee Standard Media Type Max. Distance Port Module Fiber Connecting Ethernet MediaConnecting Fiber Optic ST-type, twist-lock CopperConnecting Single-Mode Fiber Optic Connecting Fiber Optic SC-type, Snap-InMedia Ieee Standard Table-Top or Shelf Mounting Rack-mounting for 19 Retma racks, regular Magnum 6K25s 1 Mountings for Magnum 6K25 units rack-mounted in a frameRack-mounting, Reverse version of the Magnum 6K25s Powering the Magnum Managed Fiber Switch2 Reverse Magnum 6K25 units, rack-mounted in a frame 6K25 Port Module 6KPM Installation Preparation for Installing and Removing 6KPMs Remove Chassis CoverInstalling 6KPM Cards in the Magnum 6K25 1c Top View 6KPM retaining screws hold Face PlateUplink 2f Securely latching up 6KPM Cards into a Magnum 6K25 2g Top View 6KPM Module installed inside a 6K25 Removing 6KPM Cards 3b Removing a 6KPM CardDB-9 Console port connector Connecting the Console Terminal to Magnum 6K25 ManagementPin Signal Description Console DB-9 PortSwitching Functionality Filtering and ForwardingUp-link MDI-MDIX on RJ-45 port modules, for port 1 only Status LEDsAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports Www . GarrettCom . com Flow-control, Ieee 802.3x standard 6KP4 ’cvrIntroduction Magnum 6K25 Managed Fiber Switch Port Modules ZXSC706KPM Module Description 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module @10Mb @100Mb Multi-mode FX-ST twist 1c 6KP4Lock Module Copper ports and 2 Single Mode SC-type connectors. It Provides an advantageFiber functions in one Module of the 6K25 Switch Through combining copperDistances up the IEEE-standard Port@ 100Mbps Multi-Mode Fiber port100Mbps distance limits, i.e Copper and fiber Small Form Factor Magnum 6KP8-45MTModule is a combo module with Placing more ports on one module100Mbps multi-mode LC Connector Small6KP8-MLC, 8 ports @ Form Factor9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port PoE LEDs Summary Fig. the top 8-RJ45 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 14 6KM-BLNK When Calling for Assistance Before Calling for AssistanceNo Problem Found Return Material Authorization RMA ProcedureShipping and Packaging Information Appendix a Warranty Information Appendix B Internal DC Power Supply OptionsB3.0 Applications for DC Powered Switches B4.1 UL Requirements for DC-powered units B4.0Appendix C Internal DC Dual-Source Power Option B5.0 OperationC4.0 Features and Benefits of the DUAL-SOURCE Design Example Magnum 6K25R-48VDC C5.1 UL RequirementsExample Magnum 6K25R-24VDC or Magnum 6K25R-125VDC
Related manuals
Manual 68 pages 23.74 Kb
Top Page Image Contents