GarrettCom 6K25 Connecting Ethernet Media, Connecting Fiber Optic ST-type, twist-lock, Copper

Page 29

Magnum 6K25 Managed Fiber Switch

Installation and User Guide (04/06)

3.2Connecting Ethernet Media

The Magnum 6K25 Switches are specifically designed to support all standard Ethernet media types within a single Switch unit. This is accomplished by using a family of different port Modules which can be individually selected and configured per-port. See Section 2.4 for a description of the PMs.

The various media types supported along with the corresponding IEEE

802.3 and 802.3u standards and connector types are as follows:

IEEE Standard

Media Type

Max. Distance

Port Module

Fiber:

mm1 Fiber

 

 

100BASE-FX

220m ( ft) GBIC-SXSC

 

sgl.m2 Fiber

5Km

GBIC-LXSC

100BASE-FX

mm1 Fiber

2.0km (6,562 ft)

6K6-MSC, -MST

 

sgl.m2 Fiber

18.0km (95K ft)

SSC, SSCL

small form factor

mm1 Fiber

2.0km (6,562 ft)

6K8-MTRJ, -MLC

small form factor

sgl.m1 Fiber

15 km

6KP8- SLC

Copper:

 

 

10BASE-T and 100BASE-TX twisted pair

100m (328 ft)

6K8-RJ45

1 mm = multi-mode

2 sgl.m = single-mode

 

3.2.1Connecting Fiber Optic ST-type, “twist-lock”

The following procedure applies to installations using a PM with ST-type fiber connectors. This procedure applies to ports using a 6K25 module, MST-type port.

1.Before connecting the fiber optic cable, remove the protective dust caps from the tips of the connectors on the PM. Save these dust caps for future use.

2.Wipe clean the ends of the dual connectors with a soft cloth or lint-free lens tissue dampened in alcohol. Make certain the connectors are clean before connecting.

Note: One strand of the duplex fiber optic cable is coded using color bands at regular intervals; you must use the color-coded strand on the associated ports at each end of the fiber optic segment.

3.Connect the Transmit (TX) port (light colored post) on the Magnum PM to the Receive (RX) port of the remote device. Begin with the color-coded strand of the cable for this first TX-to-RX connection.

4.Connect the Receive (RX) port (dark colored post on the PM) to the Transmit

(TX) port of the remote device. Use the non-color coded fiber strand for this.

5.The LINK LED on the front of the PM will illuminate when a proper connection has been established at both ends (and when power is ON in the unit). If LINK is not lit after cable connection, the normal cause is improper cable polarity. Swap the fiber cables at the PM connector to remedy this situation.

www. GarrettCom . com

22

Image 29
Contents Managed Fiber Switch Trademarks Canadian Emission Contacting GarrettCom, IncSpecifications Troubleshooting Revisions Magnum Line Performance Technical SpecificationsNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsFiber Single-mode connector types Fiber Multi-mode connector types supportedManagement Console connector Power Supply InternalNebs Testing and Certification Nebs certified Alarm Contact OptionalPer-port MDI or Mdix on RJ-45 Agency ApprovalsOrdering Information 6K PoE Modules with 48VDC Pass-Through For Gigabit module configuration options6K PoE Modules with 48VDC Power Inside Introduction Inspecting the Package and Product Product Description Magnum 6K25 Managed Fiber Switch Magnum 6K25 and 6K25R chassis 1a Regular 6K25 front view, configured for 24 +1 Gb portsEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 The 6K25-Series’s8-port New PoEPower Inside, model PI6KP8-45RJ MDIX, 10/100Mb 8-port ACT LK RX Gigabit 1000Mbps port modules Four-Port 10 Mb mm Fiber ST Modules@ 1000Mb Fiber SC + 4@10/ 100Mb Packet Prioritization, 802.1p QOSFrame Buffering and Flow Control GarrettCom proprietary MIBs for Snmp Managed Network Software MNS-6K for Magnum 6K25-Series„ Features Fiber-Built-In „ Managed switching for high performance Ethernet LANs„ RJ-45 ports are MDI/MDIX supported „ Nebs and Etsi tested and certifiedApplications Example 1 Magnum 6K25 Switch for a Vlan applicationWww . GarrettCom . com Locating Magnum 6K25 Switches InstallationConnecting Fiber Optic ST-type, twist-lock Connecting Ethernet MediaIeee Standard Media Type Max. Distance Port Module Fiber CopperMedia Ieee Standard Connecting Fiber Optic SC-type, Snap-InConnecting Single-Mode Fiber Optic Table-Top or Shelf Mounting 1 Mountings for Magnum 6K25 units rack-mounted in a frame Rack-mounting for 19 Retma racks, regular Magnum 6K25s2 Reverse Magnum 6K25 units, rack-mounted in a frame Powering the Magnum Managed Fiber SwitchRack-mounting, Reverse version of the Magnum 6K25s 6K25 Port Module 6KPM Installation Remove Chassis Cover Preparation for Installing and Removing 6KPMs1c Top View 6KPM retaining screws hold Face Plate Installing 6KPM Cards in the Magnum 6K25Uplink 2f Securely latching up 6KPM Cards into a Magnum 6K25 2g Top View 6KPM Module installed inside a 6K25 3b Removing a 6KPM Card Removing 6KPM CardsPin Signal Description Connecting the Console Terminal to Magnum 6K25 ManagementDB-9 Console port connector Console DB-9 PortFiltering and Forwarding Switching FunctionalityAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports Status LEDsUp-link MDI-MDIX on RJ-45 port modules, for port 1 only Www . GarrettCom . com Flow-control, Ieee 802.3x standard ’cvr 6KP4ZXSC70 Introduction Magnum 6K25 Managed Fiber Switch Port Modules6KPM Module Description 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Lock Module 1c 6KP4@10Mb @100Mb Multi-mode FX-ST twist Fiber functions in one Module of the 6K25 Switch Mode SC-type connectors. It Provides an advantageCopper ports and 2 Single Through combining copper100Mbps distance limits, i.e Port@ 100Mbps Multi-Mode Fiber portDistances up the IEEE-standard Module is a combo module with Magnum 6KP8-45MTCopper and fiber Small Form Factor Placing more ports on one module6KP8-MLC, 8 ports @ Connector Small100Mbps multi-mode LC Form Factor9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port PoE LEDs Summary Fig. the top 8-RJ45 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 14 6KM-BLNK Before Calling for Assistance When Calling for AssistanceShipping and Packaging Information Return Material Authorization RMA ProcedureNo Problem Found Appendix B Internal DC Power Supply Options Appendix a Warranty InformationB3.0 Applications for DC Powered Switches B4.0 B4.1 UL Requirements for DC-powered unitsB5.0 Operation Appendix C Internal DC Dual-Source Power OptionC4.0 Features and Benefits of the DUAL-SOURCE Design Example Magnum 6K25R-24VDC or Magnum 6K25R-125VDC C5.1 UL RequirementsExample Magnum 6K25R-48VDC
Related manuals
Manual 68 pages 23.74 Kb