GarrettCom 6K25 manual Preparation for Installing and Removing 6KPMs, Remove Chassis Cover

Page 35

Magnum 6K25 Managed Fiber Switch

Installation and User Guide (04/06)

required 6KPM modules installed. There may be situations where 6KPM cards need to be added or replaced. In cases where additional 6KPM cards are needed, the faceplate for an available front-mounted slot must be removed. The following procedure describes this operation.

3.5.1 Preparation for Installing and Removing 6KPMs

STOP!!!

Be sure the power cord and connections for all powers single or dual, is unplugged from the chassis before attempting to remove and/or replace any PM cards.

Failure to do so may result in damage to the unit

and will void the warranty.

Caution- Avoid Static Discharge: The port modules (like most electronic equipment) are sensitive to static discharge. Use proper ESD measures when handling port modules.

Step 1. Make sure the 6KPM Card package has all necessary accessories to install it properly. Each 6KPM Card package except the Gigabit, for field installation contains (Daughterboard (Bigger) and Granddaughter board (smaller), three 5/8 stand offs for Granddaughter board, six #4-40 Pan-Head screws along with Front panel face plate package. The Front panel faceplate package includes 3 retainer brackets and six #2-56 flat head screws.

NOTE: Every 6KPM Card package comes with their matching Daughter and Granddaughter board. The copper 6KPM card should not work properly if mixed with other Fiber combo 6KPM card packages. Always install the PM module separately one by one to avoid the mixing.

Step 2. Remove Chassis Cover

The Magnum 6K25 chassis are combined with top and bottom parts and assembled together with the help of 22 Philips-head screws. There are 7 screws located on the front-bottom and rear-top of the unit and four screws each on the sides. Remove these screws. Once these are removed, the top cover is easily lifted off the chassis base. When the chassis top cover has been removed, the interior of the unit is exposed.

Figure 3.5.1a: Removing Chassis Cover

www . GarrettCom . com

28

Image 35

Contents Managed Fiber Switch Trademarks Canadian Emission Contacting GarrettCom, IncSpecifications Troubleshooting Revisions Magnum Line Maximum 10 Mbps Ethernet Segment Lengths Technical SpecificationsPerformance Network Standards and Compliance, hardwarePower Supply Internal Fiber Multi-mode connector types supportedFiber Single-mode connector types Management Console connectorAgency Approvals Alarm Contact OptionalNebs Testing and Certification Nebs certified Per-port MDI or Mdix on RJ-45Ordering Information 6K PoE Modules with 48VDC Pass-Through For Gigabit module configuration options6K PoE Modules with 48VDC Power Inside Introduction Inspecting the Package and Product Product Description Magnum 6K25 Managed Fiber Switch Magnum 6K25 and 6K25R chassis 1a Regular 6K25 front view, configured for 24 +1 Gb portsEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 The 6K25-Series’s8-port New PoEPower Inside, model PI6KP8-45RJ MDIX, 10/100Mb 8-port ACT LK RX Gigabit 1000Mbps port modules Four-Port 10 Mb mm Fiber ST Modules@ 1000Mb Fiber SC + 4@10/ 100Mb Packet Prioritization, 802.1p QOSFrame Buffering and Flow Control GarrettCom proprietary MIBs for Snmp Managed Network Software MNS-6K for Magnum 6K25-Series„ Features Fiber-Built-In „ Managed switching for high performance Ethernet LANs„ RJ-45 ports are MDI/MDIX supported „ Nebs and Etsi tested and certifiedApplications Example 1 Magnum 6K25 Switch for a Vlan applicationWww . GarrettCom . com Locating Magnum 6K25 Switches InstallationCopper Connecting Ethernet MediaConnecting Fiber Optic ST-type, twist-lock Ieee Standard Media Type Max. Distance Port Module FiberMedia Ieee Standard Connecting Fiber Optic SC-type, Snap-InConnecting Single-Mode Fiber Optic Table-Top or Shelf Mounting 1 Mountings for Magnum 6K25 units rack-mounted in a frame Rack-mounting for 19 Retma racks, regular Magnum 6K25s2 Reverse Magnum 6K25 units, rack-mounted in a frame Powering the Magnum Managed Fiber SwitchRack-mounting, Reverse version of the Magnum 6K25s 6K25 Port Module 6KPM Installation Remove Chassis Cover Preparation for Installing and Removing 6KPMs1c Top View 6KPM retaining screws hold Face Plate Installing 6KPM Cards in the Magnum 6K25Uplink 2f Securely latching up 6KPM Cards into a Magnum 6K25 2g Top View 6KPM Module installed inside a 6K25 3b Removing a 6KPM Card Removing 6KPM CardsConsole DB-9 Port Connecting the Console Terminal to Magnum 6K25 ManagementPin Signal Description DB-9 Console port connectorFiltering and Forwarding Switching FunctionalityAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports Status LEDsUp-link MDI-MDIX on RJ-45 port modules, for port 1 only Www . GarrettCom . com Flow-control, Ieee 802.3x standard ’cvr 6KP4ZXSC70 Introduction Magnum 6K25 Managed Fiber Switch Port Modules6KPM Module Description 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Lock Module 1c 6KP4@10Mb @100Mb Multi-mode FX-ST twist Through combining copper Mode SC-type connectors. It Provides an advantageFiber functions in one Module of the 6K25 Switch Copper ports and 2 Single100Mbps distance limits, i.e Port@ 100Mbps Multi-Mode Fiber portDistances up the IEEE-standard Placing more ports on one module Magnum 6KP8-45MTModule is a combo module with Copper and fiber Small Form FactorForm Factor Connector Small6KP8-MLC, 8 ports @ 100Mbps multi-mode LC9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port PoE LEDs Summary Fig. the top 8-RJ45 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 14 6KM-BLNK Before Calling for Assistance When Calling for AssistanceShipping and Packaging Information Return Material Authorization RMA ProcedureNo Problem Found Appendix B Internal DC Power Supply Options Appendix a Warranty InformationB3.0 Applications for DC Powered Switches B4.0 B4.1 UL Requirements for DC-powered unitsB5.0 Operation Appendix C Internal DC Dual-Source Power OptionC4.0 Features and Benefits of the DUAL-SOURCE Design Example Magnum 6K25R-24VDC or Magnum 6K25R-125VDC C5.1 UL RequirementsExample Magnum 6K25R-48VDC

Related manuals

Manual 68 pages 23.74 Kb