GarrettCom 6K25 manual Connecting Fiber Optic SC-type, Snap-In, Connecting Single-Mode Fiber Optic

Page 30

Magnum 6K25 Managed Fiber Switch

Installation and User Guide (04/06)

3.2.2Connecting Fiber Optic SC-type, "Snap-In"

The following procedure applies to installations using a PM with SC-type fiber

connectors, i.e., using 6K-MSC, 6K-SSC single-mode.

When connecting fiber media to SC connectors, simply snap on the two square male connectors into the SC female jacks of the 6KPM until it clicks and secures.

3.2.3Connecting Single-Mode Fiber Optic

When using single-mode fiber cable, be sure to use single-mode fiber port

connectors. Single-mode fiber cable has a smaller diameter than multi-mode fiber cable (9/125 microns for single-mode, 50/125 or 62.5/125 microns for multi-mode where xx/xx are the diameters of the core and the core plus the cladding respectively). Single-mode fiber allows full bandwidth at longer distances, and may be used to connect 10 Mb nodes up to 10 Km apart, or 18Km with the 6K-SSC.

The same procedures as for multi-mode fiber applies to single-mode fiber connectors. Follow the steps listed in Section 3.2.2 above.

3.2.4Connecting Twisted Pair (RJ-45,CAT3, CAT5, Unshielded or Shielded) The RJ-45 ports of the Magnum 6K25 can be connected to the following two

media types: 100BASE-TX and 10BASE-T. CAT 5 cables should be used when making 100BASE-TX connections. When the ports are used as 10BASE-T ports, CAT 3 may be used. In either case, the maximum distance for unshielded twisted pair cabling is 100 meters (328 ft).

Media

IEEE Standard

Connector

Twisted Pair (CAT 3, 4, 5)

10BASE-T

RJ-45

Twisted Pair (CAT 5)

100BASE-TX

RJ-45

NOTE : It is recommended that high quality CAT. 5 cables (which work for both 10 Mb and 100Mb) be used whenever possible in order to provide flexibility in a mixed-speed network, since dual-speed ports are auto-sensing for either 10 and 100Mb/s.

The following procedure describes how to connect a 10BASE-T or 100BASE- TX twisted pair segment to the RJ-45 port. The procedure is the same for both unshielded and shielded twisted pair cables.

1.Using standard twisted pair media, insert either end of the cable with an RJ-45 plug into the RJ-45 connector of the port. Note that, even though the connector is shielded, either unshielded or shielded cables and wiring may be used.

2.Connect the other end of the cable to the corresponding device

3.Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established

www. GarrettCom . com

23

Image 30
Contents Managed Fiber Switch Trademarks Contacting GarrettCom, Inc Canadian EmissionSpecifications Troubleshooting Revisions Magnum Line Network Standards and Compliance, hardware Technical SpecificationsPerformance Maximum 10 Mbps Ethernet Segment LengthsManagement Console connector Fiber Multi-mode connector types supportedFiber Single-mode connector types Power Supply InternalPer-port MDI or Mdix on RJ-45 Alarm Contact OptionalNebs Testing and Certification Nebs certified Agency ApprovalsOrdering Information For Gigabit module configuration options 6K PoE Modules with 48VDC Pass-Through6K PoE Modules with 48VDC Power Inside Introduction Inspecting the Package and Product Product Description Magnum 6K25 Managed Fiber Switch 1a Regular 6K25 front view, configured for 24 +1 Gb ports Magnum 6K25 and 6K25R chassisEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 The 6K25-Series’s8-port New PoEPower Inside, model PI6KP8-45RJ MDIX, 10/100Mb 8-port ACT LK RX Four-Port 10 Mb mm Fiber ST Modules Gigabit 1000Mbps port modulesPacket Prioritization, 802.1p QOS Frame Buffering and Flow Control@ 1000Mb Fiber SC + 4@10/ 100Mb Managed Network Software MNS-6K for Magnum 6K25-Series GarrettCom proprietary MIBs for Snmp„ Managed switching for high performance Ethernet LANs „ Features Fiber-Built-In„ Nebs and Etsi tested and certified „ RJ-45 ports are MDI/MDIX supportedExample 1 Magnum 6K25 Switch for a Vlan application ApplicationsWww . GarrettCom . com Installation Locating Magnum 6K25 SwitchesIeee Standard Media Type Max. Distance Port Module Fiber Connecting Ethernet MediaConnecting Fiber Optic ST-type, twist-lock CopperConnecting Fiber Optic SC-type, Snap-In Connecting Single-Mode Fiber OpticMedia Ieee Standard Table-Top or Shelf Mounting Rack-mounting for 19 Retma racks, regular Magnum 6K25s 1 Mountings for Magnum 6K25 units rack-mounted in a framePowering the Magnum Managed Fiber Switch Rack-mounting, Reverse version of the Magnum 6K25s2 Reverse Magnum 6K25 units, rack-mounted in a frame 6K25 Port Module 6KPM Installation Preparation for Installing and Removing 6KPMs Remove Chassis CoverInstalling 6KPM Cards in the Magnum 6K25 1c Top View 6KPM retaining screws hold Face PlateUplink 2f Securely latching up 6KPM Cards into a Magnum 6K25 2g Top View 6KPM Module installed inside a 6K25 Removing 6KPM Cards 3b Removing a 6KPM CardDB-9 Console port connector Connecting the Console Terminal to Magnum 6K25 ManagementPin Signal Description Console DB-9 PortSwitching Functionality Filtering and ForwardingStatus LEDs Up-link MDI-MDIX on RJ-45 port modules, for port 1 onlyAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports Www . GarrettCom . com Flow-control, Ieee 802.3x standard 6KP4 ’cvrIntroduction Magnum 6K25 Managed Fiber Switch Port Modules ZXSC706KPM Module Description 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module 1c 6KP4 @10Mb @100Mb Multi-mode FX-ST twistLock Module Copper ports and 2 Single Mode SC-type connectors. It Provides an advantageFiber functions in one Module of the 6K25 Switch Through combining copperPort@ 100Mbps Multi-Mode Fiber port Distances up the IEEE-standard100Mbps distance limits, i.e Copper and fiber Small Form Factor Magnum 6KP8-45MTModule is a combo module with Placing more ports on one module100Mbps multi-mode LC Connector Small6KP8-MLC, 8 ports @ Form Factor9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port PoE LEDs Summary Fig. the top 8-RJ45 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 14 6KM-BLNK When Calling for Assistance Before Calling for AssistanceReturn Material Authorization RMA Procedure No Problem FoundShipping and Packaging Information Appendix a Warranty Information Appendix B Internal DC Power Supply OptionsB3.0 Applications for DC Powered Switches B4.1 UL Requirements for DC-powered units B4.0Appendix C Internal DC Dual-Source Power Option B5.0 OperationC4.0 Features and Benefits of the DUAL-SOURCE Design C5.1 UL Requirements Example Magnum 6K25R-48VDCExample Magnum 6K25R-24VDC or Magnum 6K25R-125VDC
Related manuals
Manual 68 pages 23.74 Kb