GarrettCom manual Rack-mounting, Reverse version of the Magnum 6K25s

Page 33

Magnum 6K25 Managed Fiber Switch

Installation and User Guide (04/06)

3.3.2 Rack-mounting, Reverse version of the Magnum 6K25s

The optional Reverse Magnum 6K25 Model has all of the cabling (Ethernet cabling, power cabling and console port cabling) connectors in the rear, and the status LEDs in the front. The status LEDs that are co-incident with the ports are still present there, and a second or dual set of LEDs are used for status visibility in the front of the unit, showing the same data.

There are three options of brackets available to mount in the standard 19” frame or the 23” frame or ETSI (21”) frame. The 19” brackets are included with each unit, the other two may be purchased if desired.

With each bracket type, there are three different mounting options is shown in Fig. 3.3.2. The case of the Magnum 6K25 has mounting holes prepared for each of the mounting arrangements. Users may choose the mounting arrangement most suitable for their installation.

D		D	C		C	B		B	A	A
D	D	C		C	B		B	A		A

DD CC BB AA

Standard Flush

Mount Bracket

Mid-Range Mount or 5” Set-Back Bracket

Rear Mount Bracket

Fig 3.3.2 Reverse Magnum 6K25 units, rack-mounted in a frame

3.4Powering the Magnum Managed Fiber Switch

The Magnum 6K25 Switches incorporate an internal universal power supply

and have a recessed male IEC connector for the AC power cord at the left-rear. A manual power ON-OFF switch is adjacent. A six-foot 115 VAC 60 Hz standard power cord is supplied with each unit shipped within the United States and Canada.

The auto-ranging power supply supports installation environments where the

www . GarrettCom . com

26

Image 33

Contents Managed Fiber Switch Trademarks Canadian Emission Contacting GarrettCom, IncSpecifications Troubleshooting Revisions Magnum Line Performance Technical SpecificationsNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsFiber Single-mode connector types Fiber Multi-mode connector types supportedManagement Console connector Power Supply InternalNebs Testing and Certification Nebs certified Alarm Contact OptionalPer-port MDI or Mdix on RJ-45 Agency ApprovalsOrdering Information 6K PoE Modules with 48VDC Pass-Through For Gigabit module configuration options6K PoE Modules with 48VDC Power Inside Introduction Inspecting the Package and Product Product Description Magnum 6K25 Managed Fiber Switch Magnum 6K25 and 6K25R chassis 1a Regular 6K25 front view, configured for 24 +1 Gb portsEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 The 6K25-Series’s8-port New PoEPower Inside, model PI6KP8-45RJ MDIX, 10/100Mb 8-port ACT LK RX Gigabit 1000Mbps port modules Four-Port 10 Mb mm Fiber ST ModulesPacket Prioritization, 802.1p QOS Frame Buffering and Flow Control@ 1000Mb Fiber SC + 4@10/ 100Mb GarrettCom proprietary MIBs for Snmp Managed Network Software MNS-6K for Magnum 6K25-Series„ Features Fiber-Built-In „ Managed switching for high performance Ethernet LANs„ RJ-45 ports are MDI/MDIX supported „ Nebs and Etsi tested and certifiedApplications Example 1 Magnum 6K25 Switch for a Vlan applicationWww . GarrettCom . com Locating Magnum 6K25 Switches InstallationConnecting Fiber Optic ST-type, twist-lock Connecting Ethernet MediaIeee Standard Media Type Max. Distance Port Module Fiber CopperConnecting Fiber Optic SC-type, Snap-In Connecting Single-Mode Fiber OpticMedia Ieee Standard Table-Top or Shelf Mounting 1 Mountings for Magnum 6K25 units rack-mounted in a frame Rack-mounting for 19 Retma racks, regular Magnum 6K25sPowering the Magnum Managed Fiber Switch Rack-mounting, Reverse version of the Magnum 6K25s2 Reverse Magnum 6K25 units, rack-mounted in a frame 6K25 Port Module 6KPM Installation Remove Chassis Cover Preparation for Installing and Removing 6KPMs1c Top View 6KPM retaining screws hold Face Plate Installing 6KPM Cards in the Magnum 6K25Uplink 2f Securely latching up 6KPM Cards into a Magnum 6K25 2g Top View 6KPM Module installed inside a 6K25 3b Removing a 6KPM Card Removing 6KPM CardsPin Signal Description Connecting the Console Terminal to Magnum 6K25 ManagementDB-9 Console port connector Console DB-9 PortFiltering and Forwarding Switching FunctionalityStatus LEDs Up-link MDI-MDIX on RJ-45 port modules, for port 1 onlyAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports Www . GarrettCom . com Flow-control, Ieee 802.3x standard ’cvr 6KP4ZXSC70 Introduction Magnum 6K25 Managed Fiber Switch Port Modules6KPM Module Description 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module 1c 6KP4 @10Mb @100Mb Multi-mode FX-ST twistLock Module Fiber functions in one Module of the 6K25 Switch Mode SC-type connectors. It Provides an advantageCopper ports and 2 Single Through combining copperPort@ 100Mbps Multi-Mode Fiber port Distances up the IEEE-standard100Mbps distance limits, i.e Module is a combo module with Magnum 6KP8-45MTCopper and fiber Small Form Factor Placing more ports on one module6KP8-MLC, 8 ports @ Connector Small100Mbps multi-mode LC Form Factor9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port PoE LEDs Summary Fig. the top 8-RJ45 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 14 6KM-BLNK Before Calling for Assistance When Calling for AssistanceReturn Material Authorization RMA Procedure No Problem FoundShipping and Packaging Information Appendix B Internal DC Power Supply Options Appendix a Warranty InformationB3.0 Applications for DC Powered Switches B4.0 B4.1 UL Requirements for DC-powered unitsB5.0 Operation Appendix C Internal DC Dual-Source Power OptionC4.0 Features and Benefits of the DUAL-SOURCE Design C5.1 UL Requirements Example Magnum 6K25R-48VDCExample Magnum 6K25R-24VDC or Magnum 6K25R-125VDC

Related manuals

Manual 68 pages 23.74 Kb