Fortinet 60c manual Using the setup wizard, To configure DNS server settings

Page 32

Using the setup wizard

NAT/Route mode installation

 

 

To configure DNS server settings

Set the primary and secondary DNS server IP addresses. Enter

config system dns

set primary <address_ip> set secondary <address_ip>

end

Example

config system dns

set primary 293.44.75.21 set secondary 293.44.75.22

end

To add a default route

Add a default route to configure where the FortiGate unit sends traffic that should be sent to an external network (usually the Internet). Adding the default route also defines which interface is connected to an external network. The default route is not required if the interface connected to the external network is configured using DHCP or PPPoE.

Set the default route to the Default Gateway IP address. Enter:

config router static edit 1

set dst 0.0.0.0 0.0.0.0 set gateway <gateway_IP> set device <interface>

end

Example

If the default gateway IP is 204.23.1.2 and this gateway is connected to WAN1:

config router static edit 1

set dst 0.0.0.0 0.0.0.0 set gateway 204.23.1.2 set device wan1

end

Using the setup wizard

From the web-based manager, you can use the setup wizard to complete the initial configuration of the FortiGate unit. For information about connecting to the web-based manager, see “Connecting to the web-based manager” on page 16.

32

01-28008-0018-20050128

Fortinet Inc.

Image 32
Contents Installation Guide January 01-28008-0018-20050128Trademarks Regulatory ComplianceTable of Contents Index Secure installation, configuration, and management IntroductionCommand line interface Web-based managerSetup wizard Document conventionsFortiGate Installation Guide FortiGate documentationRelated documentation Fortinet Knowledge CenterComments on Fortinet technical documentation FortiManager documentationFortiLog documentation Customer service and technical supportFortiMail documentation Customer service and technical support Customer service and technical support Getting started Package contents MountingTurning the FortiGate unit power on and off Power requirementsEnvironmental specifications To power on the FortiGate unitConnecting to the web-based manager To connect to the web-based managerConnecting to the command line interface CLI To connect to the CLIBits per second 9600 Data bits Parity Stop bits Flow controlQuick installation using factory defaults Go to System Network DNSFactory default FortiGate configuration settings Factory default Dhcp server configurationFactory default NAT/Route mode network configuration Factory default Transparent mode network configuration Factory default firewall configurationAdministrative access Management IPScan Factory default protection profilesStrict Planning the FortiGate configuration NAT/Route modeNAT/Route mode with multiple external network connections Example NAT/Route mode network configurationTransparent mode Example NAT/Route multiple internet connection configurationNext steps Configuration optionsWeb-based manager and setup wizard NAT/Route mode installation Preparing to configure the FortiGate unit in NAT/Route modePPPoE settings User name Password Using the web-based managerDhcp or PPPoE configuration Configuring basic settings To configure interfaces Go to System Network InterfaceTo configure DNS server settings Go to System Network DNS To add a default routeUsing the command line interface Configuring the FortiGate unit to operate in NAT/Route modeTo add/change the administrator password To configure interfacesExample Get system interfaceUsing the setup wizard To configure DNS server settingsSetup wizard settings Password External InterfaceDhcp server Internal serversSetup wizard settings Antivirus Connecting the FortiGate unit to the networksStarting the setup wizard FortiGate-60 NAT/Route mode connections FortiGate-60Configuring the networks Configuring the Modem interfaceGo to System Config Time To configure virus, attack, and spam definition updatesTo set the date and time To register the FortiGate unitGo to System Maintenance Update Center Transparent mode installation Preparing to configure Transparent modeTo change the Management IP Go to System Network Management Management IPReconnecting to the web-based manager To change to Transparent mode using the CLITo configure the management IP address To configure the default gatewayTo start the setup wizard Connecting the FortiGate unit to your network InternalTo register your FortiGate unit Go to System Maintenance Update Center High availability installation Configuring FortiGate units for HA operationHigh availability configuration settings Priorities of heartbeat device and monitor prioritiesGroup ID MAC Address To change the FortiGate unit host name Configuring FortiGate units for HA using the CLI Config system global Set hostname namestr endConnecting the cluster to your networks To configure the FortiGate unit for HA operationHA network configuration To connect the clusterInstalling and configuring the cluster Installing and configuring the cluster Redundant mode configuration Configuring the modem interfaceSelecting a modem mode Standalone mode configuration To operate in standalone mode Go to System Network ModemConfiguring modem settings ModeAuto-dial Redundant forTo connect to a dialup account Go to System Network Modem Connecting and disconnecting the modem in Standalone modeTo configure modem settings Go to System Network Modem Defining a Ping Server Dead gateway detectionTo disconnect the modem ISPAdding firewall policies for modem connections Index CLIIndex