Fortinet 60c manual Connecting the FortiGate unit to the networks, Starting the setup wizard

Page 34

Connecting the FortiGate unit to the network(s)

NAT/Route mode installation

 

 

Table 8: Setup wizard settings

Antivirus

High

Create a protection profile that enables virus

 

scanning, file blocking, and blocking of oversize

 

email for HTTP, FTP, IMAP, POP3, and SMTP. Add

 

this protection profile to a default firewall policy.

 

 

Medium

Create a protection profile that enables virus

 

scanning, for HTTP, FTP, IMAP, POP3, and SMTP

 

(recommended). Add this protection profile to a

 

default firewall policy.

 

 

None

Do not configure antivirus protection.

Select one of these security levels to protect your network from viruses.

Starting the setup wizard

1In the web-based manager, select Easy Setup Wizard.

Figure 9: Select the Easy Setup Wizard

2Follow the instructions on the wizard pages and use the information that you gathered in Table 6 on page 28 and Table 8 on page 33 to fill in the wizard fields.

3Select the Next button to step through the wizard pages.

4Confirm the configuration settings, and then select Finish and Close.

Note: If you change the IP address of the interface you are connecting to, you must connect through a web browser again using the new address. Browse to https:// followed by the new IP address of the interface. If the new IP address of the interface is on a different subnet, you may have to change the IP address of your computer to the same subnet.

Note: If you use the setup wizard to configure internal server settings, the FortiGate unit adds port forwarding virtual IPs and firewall policies for each server. For each server located on your internal network the FortiGate unit adds a WAN1->Internal firewall policy.

You are now finished the initial configuration of the FortiGate unit.

Connecting the FortiGate unit to the network(s)

When you have completed the initial configuration, you can connect the FortiGate unit between your internal network and the Internet.

The following network connections are available on the FortiGate-60 unit:

A 4-port switch for connecting the FortiGate internal interface to your internal network,

One WAN1 port for connecting to your public switch or router and the Internet,

One WAN2 port for connecting to a second public switch or router and the Internet for a redundant Internet connection,

34

01-28008-0018-20050128

Fortinet Inc.

Image 34
Contents Installation Guide January 01-28008-0018-20050128Trademarks Regulatory ComplianceTable of Contents Index Secure installation, configuration, and management IntroductionCommand line interface Web-based managerSetup wizard Document conventionsFortiGate Installation Guide FortiGate documentationComments on Fortinet technical documentation Related documentationFortinet Knowledge Center FortiManager documentationFortiMail documentation Customer service and technical supportFortiLog documentation Customer service and technical support Customer service and technical support Getting started Package contents MountingEnvironmental specifications Turning the FortiGate unit power on and offPower requirements To power on the FortiGate unitConnecting to the web-based manager To connect to the web-based managerBits per second 9600 Data bits Parity Connecting to the command line interface CLITo connect to the CLI Stop bits Flow controlQuick installation using factory defaults Go to System Network DNSFactory default FortiGate configuration settings Factory default Dhcp server configurationFactory default NAT/Route mode network configuration Administrative access Factory default Transparent mode network configurationFactory default firewall configuration Management IPStrict Factory default protection profilesScan Planning the FortiGate configuration NAT/Route modeNAT/Route mode with multiple external network connections Example NAT/Route mode network configurationTransparent mode Example NAT/Route multiple internet connection configurationWeb-based manager and setup wizard Configuration optionsNext steps NAT/Route mode installation Preparing to configure the FortiGate unit in NAT/Route modeDhcp or PPPoE configuration Using the web-based managerPPPoE settings User name Password To configure DNS server settings Go to System Network DNS Configuring basic settingsTo configure interfaces Go to System Network Interface To add a default routeTo add/change the administrator password Using the command line interfaceConfiguring the FortiGate unit to operate in NAT/Route mode To configure interfacesExample Get system interfaceUsing the setup wizard To configure DNS server settingsDhcp server Setup wizard settings PasswordExternal Interface Internal serversStarting the setup wizard Connecting the FortiGate unit to the networksSetup wizard settings Antivirus FortiGate-60 NAT/Route mode connections FortiGate-60Configuring the networks Configuring the Modem interfaceTo set the date and time Go to System Config TimeTo configure virus, attack, and spam definition updates To register the FortiGate unitGo to System Maintenance Update Center Transparent mode installation Preparing to configure Transparent modeTo change the Management IP Go to System Network Management Management IPReconnecting to the web-based manager To change to Transparent mode using the CLITo configure the management IP address To configure the default gatewayTo start the setup wizard Connecting the FortiGate unit to your network InternalTo register your FortiGate unit Go to System Maintenance Update Center High availability configuration settings High availability installationConfiguring FortiGate units for HA operation Priorities of heartbeat device and monitor prioritiesGroup ID MAC Address To change the FortiGate unit host name Configuring FortiGate units for HA using the CLI Config system global Set hostname namestr endConnecting the cluster to your networks To configure the FortiGate unit for HA operationHA network configuration To connect the clusterInstalling and configuring the cluster Installing and configuring the cluster Selecting a modem mode Configuring the modem interfaceRedundant mode configuration Standalone mode configuration To operate in standalone mode Go to System Network ModemAuto-dial Configuring modem settingsMode Redundant forTo configure modem settings Go to System Network Modem Connecting and disconnecting the modem in Standalone modeTo connect to a dialup account Go to System Network Modem To disconnect the modem Defining a Ping ServerDead gateway detection ISPAdding firewall policies for modem connections Index CLIIndex