Fortinet 60c Setup wizard settings Password, External Interface, Dhcp server, Internal servers

Page 33

NAT/Route mode installation

Using the setup wizard

 

 

If you are configuring the FortiGate unit to operate in NAT/Route mode (the default), you can use the setup wizard to:

add the administration password

configure the internal interface address

choose either a manual (static) or a dynamic (DHCP or PPPoE) address for the external interface

add a default route for the external interface

add the DNS server IP addresses

add the DHCP server settings and IP addresses

add various internal server IP addresses including web, IMAP, POP3, SMTP, and FTP servers

set the antivirus protection to high, medium, or none

Table 8 on page 33 lists the additional settings that you can configure with the setup wizard. See Table 6 on page 28 and Table 7 on page 28 for other settings.

Table 8: Setup wizard settings

Password

Prepare an administrator password.

 

 

Internal Interface

Use the information you gathered in Table 6 on page 28.

 

 

External Interface

Use the information you gathered in Table 6 on page 28.

The External interface in the setup wizard refers to the WAN1

 

interface of the FortiGate unit.

 

 

 

 

 

Starting IP:

_____._____._____._____

 

Ending IP:

_____._____._____._____

 

Netmask:

_____._____._____._____

DHCP server

Default

_____._____._____._____

 

Gateway:

 

 

DNS IP:

_____._____._____._____

 

Your FortiGate firewall contains a

DHCP server to automatically set up

 

the addresses of computers on your internal network

 

 

 

 

Web Server:

_____._____._____._____

 

SMTP Server:

_____._____._____._____

 

POP3 Server:

_____._____._____._____

Internal servers

IMAP Server:

_____._____._____._____

 

FTP Server:

_____._____._____._____

 

If you provide access from the Internet to a web server, SMTP server,

 

POP3 server IMAP server, or FTP server installed on an internal

 

network, add the IP addresses of the servers here.

 

 

 

FortiGate-60 Installation Guide

01-28008-0018-20050128

33

Image 33
Contents January 01-28008-0018-20050128 Installation GuideRegulatory Compliance TrademarksTable of Contents Index Introduction Secure installation, configuration, and managementWeb-based manager Command line interfaceDocument conventions Setup wizardFortiGate documentation FortiGate Installation GuideFortinet Knowledge Center Related documentationComments on Fortinet technical documentation FortiManager documentationCustomer service and technical support FortiMail documentationFortiLog documentation Customer service and technical support Customer service and technical support Getting started Mounting Package contentsPower requirements Turning the FortiGate unit power on and offEnvironmental specifications To power on the FortiGate unitTo connect to the web-based manager Connecting to the web-based managerTo connect to the CLI Connecting to the command line interface CLIBits per second 9600 Data bits Parity Stop bits Flow controlGo to System Network DNS Quick installation using factory defaultsFactory default Dhcp server configuration Factory default FortiGate configuration settingsFactory default NAT/Route mode network configuration Factory default firewall configuration Factory default Transparent mode network configurationAdministrative access Management IPFactory default protection profiles StrictScan NAT/Route mode Planning the FortiGate configurationExample NAT/Route mode network configuration NAT/Route mode with multiple external network connectionsExample NAT/Route multiple internet connection configuration Transparent modeConfiguration options Web-based manager and setup wizardNext steps Preparing to configure the FortiGate unit in NAT/Route mode NAT/Route mode installationUsing the web-based manager Dhcp or PPPoE configurationPPPoE settings User name Password To configure interfaces Go to System Network Interface Configuring basic settingsTo configure DNS server settings Go to System Network DNS To add a default routeConfiguring the FortiGate unit to operate in NAT/Route mode Using the command line interfaceTo add/change the administrator password To configure interfacesGet system interface ExampleTo configure DNS server settings Using the setup wizardExternal Interface Setup wizard settings PasswordDhcp server Internal serversConnecting the FortiGate unit to the networks Starting the setup wizardSetup wizard settings Antivirus FortiGate-60 FortiGate-60 NAT/Route mode connectionsConfiguring the Modem interface Configuring the networksTo configure virus, attack, and spam definition updates Go to System Config TimeTo set the date and time To register the FortiGate unitGo to System Maintenance Update Center Preparing to configure Transparent mode Transparent mode installationManagement IP To change the Management IP Go to System Network ManagementTo change to Transparent mode using the CLI Reconnecting to the web-based managerTo configure the default gateway To configure the management IP addressTo start the setup wizard Internal Connecting the FortiGate unit to your networkTo register your FortiGate unit Go to System Maintenance Update Center Configuring FortiGate units for HA operation High availability installationHigh availability configuration settings Priorities of heartbeat device and monitor prioritiesGroup ID MAC Address To change the FortiGate unit host name Config system global Set hostname namestr end Configuring FortiGate units for HA using the CLITo configure the FortiGate unit for HA operation Connecting the cluster to your networksTo connect the cluster HA network configurationInstalling and configuring the cluster Installing and configuring the cluster Configuring the modem interface Selecting a modem modeRedundant mode configuration To operate in standalone mode Go to System Network Modem Standalone mode configurationMode Configuring modem settingsAuto-dial Redundant forConnecting and disconnecting the modem in Standalone mode To configure modem settings Go to System Network ModemTo connect to a dialup account Go to System Network Modem Dead gateway detection Defining a Ping ServerTo disconnect the modem ISPAdding firewall policies for modem connections CLI IndexIndex