Eizo FlexScan L675 manual Connecting the signal cable, Analog Input, Digital Input

Page 15

2-2. Connecting the signal cable

•Be sure that the power switches of both the PC and the monitor are OFF.

1.Plug the signal cable into the DVI-I connector at the rear of the monitor and the other end of the cable into the video connector on the PC.

After connecting, secure the connection with the screw-in fasteners.

[Analog Input]

Connectors on rear

Video Output Connector

D-Sub mini 15 pin

·Standard graphics board ·Macintosh G3 (Blue & White) / G4

FD-C16 (enclosed)

Video Output Connector

D-Sub 15 pin

Macintosh

Macintosh Adapter (Optional)

[Digital Input]

Connectors on rear

Video Output Connector

DVI

Digital graphics board

FD-C04 (enclosed)

ENGLISH

2. CONNECTING UP 15

Image 15

Contents English Safety Symbols Table of Contents Precautions ´ Refer all servicing to qualified service personnel´ Do not dismantle the cabinet or modify the unit Keep small objects or liquids away from the unit ´ Place the unit on a strong, stable surface´ Set the unit in an appropriate location ´ Handle the power cord with care ´ The equipment must be connected to a grounded main outlet´ Use the correct voltage ´ Handle with care when carrying the unit ´ Do not touch a damaged LCD panel directly with bare hands´ Do not block the ventilation slots on the cabinet ´ Do not touch the plug with wet hands ´ Use an easily accessible power outlet´ Periodically clean the area around the plug ´ Unplug the unit before cleaning itSuggestions for Maximizing Comfort Introduction FeaturesPackage Contents Front Controls & ConnectorsRear Digital Input Before connectingCable Connection Analog InputConnecting the signal cable Analog InputDigital Input 16 2. Connecting UP Plug the other end of the power cord into a power outlet Exiting the ScreenManager How to use the ScreenManagerMaking Adjustments and Settings Entering the ScreenManagerMain menu Sub menu Reference ScreenManager Adjustments and SettingsAdjustment Lock Useful FunctionsEizo Logo Disappearing function Off Timer ProcedureOff timer system Push the Auto adjustment button on the front panel AdjustmentScreen Adjustment Adjustment Procedure for Analog InputHorizontal flickering, blurring or bars appear on the screen Screen position is incorrect Use the Position adjustment Auto Set the Contrast of the screen Use the Contrast adjustmentSet the Brightness of the screen Use the Resolution adjustmentScreen position is incorrect Set the Contrast of the screenDisplaying a low resolutions 28 4. Adjustment Before the Color adjustment Color AdjustmentTo change the flesh color, etc Use the Hue adjustment To change the saturation Use the Saturation adjustmentPower saving system Power-save SetupTo use the PC’s power saving system Vesa Dpms To set the power save with ScreenSaver software Eizo Mpms32 4. Adjustment Required system environment Connecting to the USB HUBUSB Example of connectionDigital x digital Connecting Examples Analog x DigitalMonitor Analog x AnalogSelecting the active input Priority input signalAttaching AN ARM Stand Setup Procedure38 7. Attaching AN ARN Stand Following messages TroubleshootingProblems Points to check with possible solutions No pictureAfterimages appear Too darkOr dark Auto adjustment Button does not operateScreen has defective Pixels e.g. slightly lightPC is hung up. / Change after installingSetup Frequency does notCleaning CabinetLCD Panel Vesa DDC 2B SpecificationsBeeper settings Default settingClock Color Temperature TemperatureGlossary AfterimageResolution Gain AdjustmentPhase Range AdjustmentAttaching AN ARM Stand IndexUSB 10,31,33,44 Vesa Dpms 19,31,47 Memo Appendix Appendix / Anhang / AnnexeIi Appendix 480 800 525 907 111 356 556 25.422 12.712 31.778 14.267 180 Pin Assignment Pin-Belegung Affectation des Broches Dimensions AbmessungenWhy do we have environmentally labelled computers? CongratulationsWhat does labelling involve? CFCs freons Environmental requirements Flame retardantsCadmium MercuryWe, the Responsible Party Warland Drive, Cypress, CAPhone 562 431