Eizo FlexScan L675 manual Cleaning, Cabinet, LCD Panel

Page 43

9. CLEANING

Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime.

• Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol), abrasive cleaners, or other strong solvents, as these may cause damage to the cabinet or LCD panel.

Cabinet

To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild detergent. Do not spray wax or cleaner directly onto the cabinet.

LCD Panel

The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.

If necessary, stubborn stains can be removed by moistening part of a cloth with water to enhance its cleaning power.

ENGLISH

9. CLEANING 43

Image 43

Contents English Safety Symbols Table of Contents ´ Refer all servicing to qualified service personnel Precautions´ Do not dismantle the cabinet or modify the unit ´ Place the unit on a strong, stable surface Keep small objects or liquids away from the unit´ Set the unit in an appropriate location ´ The equipment must be connected to a grounded main outlet ´ Handle the power cord with care´ Use the correct voltage ´ Do not touch a damaged LCD panel directly with bare hands ´ Handle with care when carrying the unit´ Do not block the ventilation slots on the cabinet ´ Do not touch the plug with wet hands ´ Use an easily accessible power outlet´ Periodically clean the area around the plug ´ Unplug the unit before cleaning itSuggestions for Maximizing Comfort Introduction FeaturesPackage Contents Front Controls & ConnectorsRear Digital Input Before connectingCable Connection Analog InputAnalog Input Connecting the signal cableDigital Input 16 2. Connecting UP Plug the other end of the power cord into a power outlet Exiting the ScreenManager How to use the ScreenManagerMaking Adjustments and Settings Entering the ScreenManagerMain menu Sub menu Reference ScreenManager Adjustments and SettingsUseful Functions Adjustment LockEizo Logo Disappearing function Procedure Off TimerOff timer system Push the Auto adjustment button on the front panel AdjustmentScreen Adjustment Adjustment Procedure for Analog InputHorizontal flickering, blurring or bars appear on the screen Screen position is incorrect Use the Position adjustment Auto Set the Contrast of the screen Use the Contrast adjustmentSet the Brightness of the screen Use the Resolution adjustmentScreen position is incorrect Set the Contrast of the screenDisplaying a low resolutions 28 4. Adjustment Before the Color adjustment Color AdjustmentTo change the flesh color, etc Use the Hue adjustment To change the saturation Use the Saturation adjustmentPower saving system Power-save SetupTo use the PC’s power saving system Vesa Dpms To set the power save with ScreenSaver software Eizo Mpms32 4. Adjustment Required system environment Connecting to the USB HUBUSB Example of connectionDigital x digital Connecting Examples Analog x DigitalMonitor Analog x AnalogSelecting the active input Priority input signalAttaching AN ARM Stand Setup Procedure38 7. Attaching AN ARN Stand Following messages TroubleshootingProblems Points to check with possible solutions No pictureAfterimages appear Too darkOr dark Auto adjustment Button does not operateScreen has defective Pixels e.g. slightly lightPC is hung up. / Change after installingSetup Frequency does notCabinet CleaningLCD Panel Vesa DDC 2B SpecificationsBeeper settings Default settingClock Color Temperature TemperatureGlossary AfterimageResolution Gain AdjustmentPhase Range AdjustmentAttaching AN ARM Stand IndexUSB 10,31,33,44 Vesa Dpms 19,31,47 Memo Appendix Appendix / Anhang / AnnexeIi Appendix 480 800 525 907 111 356 556 25.422 12.712 31.778 14.267 180 Pin Assignment Pin-Belegung Affectation des Broches Dimensions AbmessungenCongratulations Why do we have environmentally labelled computers?What does labelling involve? CFCs freons Environmental requirements Flame retardantsCadmium MercuryWarland Drive, Cypress, CA We, the Responsible PartyPhone 562 431