Eizo S1932 manual FCC Declaration of Conformity

Page 39

For U.S.A. , Canada, etc. (rated 100-120 Vac) Only

 

FCC Declaration of Conformity

We, the Responsible Party

 

EIZO NANAO TECHNOLOGIES INC.

 

 

5710 Warland Drive, Cypress, CA 90630

 

 

 

 

 

Phone: (562) 431-5011

declare that the product

 

 

 

Trade name: EIZO

 

 

 

 

 

Model: FlexScan S1932

is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

*Reorient or relocate the receiving antenna.

*Increase the separation between the equipment and receiver.

*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

*Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note

Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the limits of a Class B digital device.

-AC Cord

-Shielded Signal Cable (enclosed)

Canadian Notice

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.

37

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Contents Eizo Nanao Corporation To use the monitor comfortably Contents Features Features and OverviewIndicator status Operation status Buttons and IndicatorsOr selecting to decrease it Example Operation methodIcon Function Overview Adjustment menu icon listSelects a language for Utility Disk Disk contents and software overviewConnection To use ScreenManager Pro for LCDDigital Input Screen AdjustmentTo eliminate vertical bars Clock To remove flickering or blurring PhaseTo correct screen position Position Color Adjustment To select the display mode FineContrast modeMode Purpose Icon Function FineContrast mode To perform advanced adjustmentsAdjustment items in each mode To adjust the brightness BrightnessTo adjust the gamma value Gamma To adjust the contrast ContrastTo adjust the color temperature Temperature To adjust the gain value GainTo adjust the color saturation Saturation To set Enable/Disable of the contrast enhancer Cont Enhancer To adjust the hue HueTurning off the monitor automatically Off Timer Adjusting Sharpness SharpnessLocking Buttons Key Lock Menu Lock Displaying Monitor Infomation Info1 Info2Enabling/Disabling DDC/CI communication DDC/CI Setting Power Indicator ON/OFF Power LED Setting Language LanguageDisplaying Eizo logo Resuming the Default Setting Reset To reset color adjustment valuesTo reset all adjustments to the factory default settings Connecting Two PCs to the Monitor To switch the input signalConnection examples Setting auto-selection of the input signal Input Signal Characters are blurred Problems Possible cause and remedy No pictureMessage below appears Screen is too bright or too darkNoise appears on the screen Adjustment menu does not appearScreen Outline of the letters are coloredAttach the monitor to the arm or stand Attaching an ArmCleaning Power Saving ModeSpecifications Main default settings factory settings Outside Dimensions Height adjustable stand Outside Dimensions Tilt standOutside Dimensions EZ-UP stand Outside Dimensions ArcSwing2 standOption List Connector Pin AssignmentPin No Signal Contact No Signal RemarksGlossary SRGB Standard RGB ResolutionTemperature Tmds Transition Minimized Differential SignalingVertical Hz Preset TimingFrequency Mode Dot clock PolarityFor more information, please visit FCC Declaration of Conformity Hinweis zur Ergonomie 4th Edition-March
Top Page Image Contents