Enterasys Networks 2000 manual Cabling and Connector Specifications, LEDs

Page 28

Hardware Overview

Cabling and Connector Specifications

The following table lists the media specifications for the 10/100BASE-TX expansion module.

Table 5. 10/100BASE-TX expansion module specifications

Port Type		Specification

10Base-T	•	802.3 standard
	• RJ-45 connector wired as Media Data Interface Crossed (MDIX); see
		10/100BASE-TX Expansion Module on page 34 for pin assignments
	• EIA Category 3, 4, or 5 unshielded twisted pair cabling
	• Maximum 328 feet (100 meters) segment length

100Base-TX	•	802.3u standard
	• RJ-45 connector wired as Media Data Interface Crossed (MDIX); see
		10/100BASE-TX Expansion Module on page 34 for pin assignments
	• EIA Category 5 unshielded twisted pair cabling
	• Maximum 100 meters (328 feet) segment length

LEDs

The 10/100BASE-TX expansion module uses the following LEDs.

Table 6. 10/100BASE-TX expansion module LEDs

LED	Description

Link	Each port has two LEDs on its connector. The green LED on the left side of
	the connector indicates the link status. When this LED is lit, the port
	hardware is detecting that a cable is plugged into the port and the port has
	established communication with the device at the other end.

Activity	The amber LED on the right side of each port connector flashes each time
	the port’s transceiver sends or receives packets.

12	Enterasys X-Pedition 2000 Getting Started Guide

Image 28

Contents 2000 Page FCC Notice Enterasys X-Pedition 2000 Getting Started Guide Enterasys NETWORKS, INC Program License Agreement Enterasys X-Pedition 2000 Getting Started Guide Enterasys X-Pedition 2000 Getting Started Guide Vii Declaration of Conformity Contents Hardware Installation Appendix a Troubleshooting IndexContents Xii Enterasys X-Pedition 2000 Getting Started Guide How to Use this Guide What’s NewWho should Read this Guide? If You Want To SeeGetting Help Related DocumentationFor Information About See Preface Preface Xvi Enterasys X-Pedition 2000 Getting Started Guide Chapter Features Overview SpecificationsRmon IPX RIP, SAPSnmp Features TCP/UDP ServicesTCP/UDP services TCP Port UDP Port Description LLCPort and Protocol VLANs BridgingRouting IP Multicast Routing IP RoutingIPX Routing Layer-4 Switching SecurityQuality of Service StatisticsManagement Platforms VlanHardware Overview Chassis Motherboard Features Boot Flash External Controls Status LEDs LED Label DescriptionFans Power SuppliesRAM Memory Expansion Modules 10/100BASE-TX Expansion ModuleLEDs Cabling and Connector Specifications100BASE-TX expansion module LEDs 100BASE-FX Expansion Module Front panel of 100BASE-FX expansion moduleBASE-FX expansion module LEDs 1000BASE-SX Expansion ModuleBASE-SX expansion module LEDs 1000BASE-LX Expansion Module Front panel of 1000BASE-LX expansion moduleBASE-LX expansion module LEDs Dual Serial and Quad Serial C/CE Expansion Modules Front panel of Dual Serial WAN expansion moduleDual Serial and Quad Serial C/CE WAN expansion module LEDs Dual Hssi Line Card Port Type SpecificationHssi LED Page Safety Considerations Preventing InjuryHardware Specifications Installing the HardwareXP-2000 physical and environmental specifications Preventing Equipment DamageVerifying Your Shipment Table-Top Installation Installing the ChassisRack Mount Installation Installing the XP-2000 chassis in an equipment rack Connecting Power to the Chassis Installing an Expansion ModuleInstalling the new face plate view from inside chassis Front of XP-2000 Attaching the Console Management Cables Nteras ys Net worksConnecting to the Serial Port Plugging into the XP-2000’s serial DB-9 DCE portConnecting to the 10/100Base-TX Port Plugging into the XP-2000’s 10/100Base-TX portAttaching Port Cables RXD receive data TXD transmit dataPlugging an ethernet cable into a 10/100BASE-TX port 100BASE-TX RJ-45 connector 1000BASE-SX and 1000BASE-LX Expansion Modules LFH-60 high density connector pin assignments Pin Signal P2GND P1TXCA P2CTSB P1RXCA P1GND P1TXDBP2SCTEB P1LLA P2RXCA P1GND P2SCTEA P1SHIELD Pin Signal Pin Hssi connector Page Chapter Firmware Installation Setup Powering On and Booting the FirmwareStarting the Command Line Interface Access ModesBasic Line Editing Commands Some commonly used CLI commands Key sequence CommandSetting Basic System Information Here is an exampleEnter yes or y to activate the changes Setting Up Snmp Community Strings Enter the copy active to startup commandSetting Up Snmp Community Strings READ-WRITE Setting Up Passwords Xp-1#system show active-configSetting the DNS Domain Name and Address Xp-1#pingSetting Syslog Parameters System set dns server IP-address IP-address IP-addressSetting Syslog Parameters Ping IP-addr Loading System Image Firmware System image add IPaddr-of-TFTP-host image-file-name Enter the system image list command to verify the change Loading Boot Prom Firmware Xp-1#system promimage upgrade 10.50.11.12 prom2Upgrading the VFS Activating the Configuration Commands in the Scratchpad Viewing the Current ConfigurationCommand like stp enable et.*.* would be displayed as follows Appendix a Troubleshooting If you experience this difficulty Try this remedyUse the procedure in Activating the Configuration Appendix B Technical Support Getting Help Numerics DvmrpIPX SAP IgmpNvram Layer-4 flow 6 services User mode VLANs UDPIndex Enterasys X-Pedition 2000 Getting Started Guide

Related manuals

Manual 188 pages 39.25 Kb