Enterasys Networks 2000 manual Setting Syslog Parameters

Page 69

Setting SYSLOG Parameters

6.Use the following command to “add” one or more DNS servers to the XP-2000:

system set dns server ["]<IP-address> [<IP-address>] [<IP-address>]["]

where <IP-address>is the IP address of the DNS server. You can specify up to three DNS servers.

Note: If you specify more than one IP address, you must separate the addresses with a space and surround them with a single pair of quotes. You do not need to surround a single IP address with quotes.

7.Enter the save active command to activate the commands and enter yes or y to activate the changes.

Here is an example of the commands above featuring the addition of two DNS server IP addresses:

xp-1# config

xp-1(config)#system set dns domain “mktg.company.com” xp-1(config)#system set dns server “10.50.11.12 10.50.12.11"

xp-1(config)# save active

8.Enter the system show dns command to verify the new DNS settings, as shown in the following example:

xp-1#system show dns

DNS domain: mktg.company.com, DNS server(s): 10.50.11.12 10.50.12.11

9.Use the ping command to verify that the XP-2000 can resolve the DNS server name into its IP address, as shown in the following example:

xp-1# ping xp1

PING xp-1.mktg.company.com (10.50.11.12): 56 data bytes

64 bytes from 10.50.11.12: icmp_seq=0 ttl=255 time=0 ms

--- xp-1.mktg.company.com ping statistics ---

1 packets transmitted, 1 packets received, 0% packet loss round-trip min/avg/max = 0/0/0 ms

Setting SYSLOG Parameters

The CLI can use SYSLOG messages to communicate the following types of messages to a SYSLOG server:

•Fatal – Provide information about events that caused the XP-2000 to crash and reset.

•Error – Provide information about errors.

Enterasys X-Pedition 2000 Getting Started Guide

53

Image 69

Contents 2000 Page FCC Notice Enterasys X-Pedition 2000 Getting Started Guide Enterasys NETWORKS, INC Program License Agreement Enterasys X-Pedition 2000 Getting Started Guide Enterasys X-Pedition 2000 Getting Started Guide Vii Declaration of Conformity Contents Hardware Installation Index Appendix a TroubleshootingContents Xii Enterasys X-Pedition 2000 Getting Started Guide What’s New How to Use this GuideWho should Read this Guide? If You Want To SeeRelated Documentation Getting HelpFor Information About See Preface Preface Xvi Enterasys X-Pedition 2000 Getting Started Guide Specifications Chapter Features OverviewIPX RIP, SAP RmonSnmp TCP/UDP Services FeaturesTCP/UDP services TCP Port UDP Port Description LLCBridging Port and Protocol VLANsRouting IP Routing IP Multicast RoutingIPX Routing Security Layer-4 SwitchingStatistics Quality of ServiceManagement Platforms VlanChassis Hardware OverviewBoot Flash Motherboard FeaturesExternal Controls Status LEDs LED Label DescriptionPower Supplies FansRAM Memory 10/100BASE-TX Expansion Module Expansion ModulesCabling and Connector Specifications LEDs100BASE-TX expansion module LEDs Front panel of 100BASE-FX expansion module 100BASE-FX Expansion Module1000BASE-SX Expansion Module BASE-FX expansion module LEDsBASE-SX expansion module LEDs Front panel of 1000BASE-LX expansion module 1000BASE-LX Expansion ModuleBASE-LX expansion module LEDs Front panel of Dual Serial WAN expansion module Dual Serial and Quad Serial C/CE Expansion ModulesDual Serial and Quad Serial C/CE WAN expansion module LEDs Port Type Specification Dual Hssi Line CardHssi LED Page Preventing Injury Safety ConsiderationsInstalling the Hardware Hardware SpecificationsXP-2000 physical and environmental specifications Preventing Equipment DamageVerifying Your Shipment Installing the Chassis Table-Top InstallationRack Mount Installation Installing the XP-2000 chassis in an equipment rack Installing an Expansion Module Connecting Power to the ChassisInstalling the new face plate view from inside chassis Front of XP-2000 Nteras ys Net works Attaching the Console Management CablesPlugging into the XP-2000’s serial DB-9 DCE port Connecting to the Serial PortPlugging into the XP-2000’s 10/100Base-TX port Connecting to the 10/100Base-TX PortRXD receive data TXD transmit data Attaching Port CablesPlugging an ethernet cable into a 10/100BASE-TX port 100BASE-TX RJ-45 connector 1000BASE-SX and 1000BASE-LX Expansion Modules LFH-60 high density connector pin assignments Pin Signal P1GND P1TXDB P2GND P1TXCA P2CTSB P1RXCAP2SCTEB P1LLA P2RXCA P1GND P2SCTEA P1SHIELD Pin Signal Pin Hssi connector Page Powering On and Booting the Firmware Chapter Firmware Installation SetupAccess Modes Starting the Command Line InterfaceSome commonly used CLI commands Key sequence Command Basic Line Editing CommandsHere is an example Setting Basic System InformationEnter yes or y to activate the changes Enter the copy active to startup command Setting Up Snmp Community StringsSetting Up Snmp Community Strings READ-WRITE Xp-1#system show active-config Setting Up PasswordsXp-1#ping Setting the DNS Domain Name and AddressSystem set dns server IP-address IP-address IP-address Setting Syslog ParametersSetting Syslog Parameters Ping IP-addr Loading System Image Firmware System image add IPaddr-of-TFTP-host image-file-name Enter the system image list command to verify the change Xp-1#system promimage upgrade 10.50.11.12 prom2 Loading Boot Prom FirmwareUpgrading the VFS Viewing the Current Configuration Activating the Configuration Commands in the ScratchpadCommand like stp enable et.*.* would be displayed as follows If you experience this difficulty Try this remedy Appendix a TroubleshootingUse the procedure in Activating the Configuration Appendix B Technical Support Getting Help Dvmrp NumericsIgmp IPX SAPNvram UDP Layer-4 flow 6 services User mode VLANsIndex Enterasys X-Pedition 2000 Getting Started Guide

Related manuals

Manual 188 pages 39.25 Kb